Search results

  1. Aquabob

    re-charging power top hydrolic system after replacing hydrolic lift

    Awsome, thank you for the information.
  2. Aquabob

    re-charging power top hydrolic system after replacing hydrolic lift

    Does anyone know how I would replace the hydrolic fluid in the power top system for a convertable 1990 Fox Body, after replacing one of the hydrolic lifters. any help would be greatly apreaciated Aquabob:shrug:
  3. Aquabob

    Air cond. Clutch problem

    I replaced the Air Cond. Clutch a few weeks ago, and when I started the engine and turned on and off the Air the clutch seemed to be working fine. I have driven the car only a few times since then and the last time I drove it on the way home I noticed a strange noise comming from the engine...
  4. Aquabob

    Driver's seat tweeked

    Purfect, great feedback, thanks bunches
  5. Aquabob

    Driver's seat tweeked

    Does anyone know of a way to un-tweek the drivers seat, I suppose a big dude, or maybe a big woman really pushed back hard on the drivers seat. Its tweeked as if you are facing to the middle of the hood, just enough to look bad and feels somewhat akward. If it matters, its the 90 Gt sport seat.
  6. Aquabob

    >>>NEED HELP WITH BODY WORK<<<

    I just found a paint remover that will work on rubber bumpers. Its called REMOV ALL Stipper, I found it at a Auto Body Supply Store. It states that it is for Most Surfaces Including Steel, Aluminum, Chrome, Alloys TPO Bumpers, Rubber Seals yada yada yada. I asked what TPO Bumpers were and...
  7. Aquabob

    redoing bumper

    I had asked that question earlier and didnt get the answer I was looking for. But I found it today at a Auto Body Shop supply store. Its called REMOV ALL Stripper, it comes in a spray can and it states that it works on all of the normal metal surfaces and also works on TPO Bumpers, Rubber...
  8. Aquabob

    removing knob on the side of sport seats

    Ok, I figured it out, in case anyone else does a search for this answer, here it is. Flip the seat bottom over, the driveshaft that connects both sides together has some retainer pins on each end. the end closest to the round knob, put vice grip on the longer side and tap the side of the vice...
  9. Aquabob

    removing knob on the side of sport seats

    Ah you beat me to it. Thank you
  10. Aquabob

    removing knob on the side of sport seats

    Woops, never mind about the headrest, just figured it out.
  11. Aquabob

    removing knob on the side of sport seats

    Ah, thats just great..............lol, just may do that if I don't get any other ideas. Well now I am stuck on the headrest, I've got the old seat cover pushed up as far as I can, and I expected to find something that would allow the headrest to pull completely out of the seat back, but I don't...
  12. Aquabob

    removing knob on the side of sport seats

    I'm in the middle of re-upholstering the seats, and I am not sure how to remove the round knob on the side of the front seats. It looks like a pin that I need to tap out of the shaft, but I'm just not sure enough to keep taping on it. Anyone out there have any experience in pulling off this...
  13. Aquabob

    rubber bumper cracked paint repair

    I did some Auto Body repair way back in the early 80's, when very few bumpers were rubber, at least I never worked on any. My 90 Mustang has had some bumping and grinding done to the rubber bumpers. The paint job has cracked quite aways around the impact area. If it was metal I would just use...
  14. Aquabob

    Valve cover bolts were only finger tight?

    Thanks for the help, so where did you get the spacer from? Is that the only purpose for the spacer?
  15. Aquabob

    Valve cover bolts were only finger tight?

  16. Aquabob

    Valve cover bolts were only finger tight?

    I had a pretty good oil leak and determined that it was comming from the valve covers. Went to wrench off the bolts and found I could take everyone of them off with just a socket and my fingers. Is this normal? Do I need to get in there and retighten after a few miles? I bought the best...
  17. Aquabob

    Tricks to unplug engine wire clusters

    The two ten wire cluster plugs behind the intake manifold (one white one black), I have gotten the black one apart after a hour of finger numbing work, now I am trying to get the white one apart. Does anyone have any tricks they would like to share?
  18. Aquabob

    Tricks to unplug engine wire clusters

    The two ten wire cluster plugs behind the intake manifold (one white one black), I have gotten the black one apart after a hour of finger numbing work, now I am trying to get the white one apart. Does anyone have any tricks they would like to share?
  19. Aquabob

    Griffin Aluminum Radiator (PICS)

    The over $200 I saved will buy alot of Tylenol.
  20. Aquabob

    gas gage does'nt work

    Wow, this is great. Yes, sorry I am a newbe, I have been real busy and could not seem to get in here and post my first question and when I did I must have saw a dyslexic 5.0 and put it in the 05 section, (ya ima bonehead). Never thought I would get so much feed back so soon, thank you all. I'm...
Top Bottom
Back
Forums
Menu