Search results

  1. M

    Fastest vintage stang?

    The magazine tests and shootouts usually put the '71 Boss 351 as being the fastest of the early mustangs. Even edges out the Boss 429. _____________________________________________________ 70 Mach 1 351c FMX
  2. M

    1969 fastback question.

    I saw a 70 Fastback at a show last weekend with a 429 Cobra Jet in it. The plugs looked like a real pain in the butt to change. I was looking at it trying to figure out how to even get a couple of them out. There is no room at all. Good luck if you get it. :shrug:
  3. M

    70 Bolt in Glass for 69 (Sportsroof)

    Check out the website www.MuscleCityGlass.com they have replacement glass for thousands of vehicles. They list a new conversion from 69 to 70 windows with regulators included for $279.00 each door. :nice: ____________________________________________________ 70 Mach1 351c FMX Trying...
  4. M

    Installing a T5, is there a clutch cable adapter?

    National Parts Depot has all kinds of conversion parts listed in their catalog. they have crossmembers, clutch cable linkage adapters,hydraulic clutch adapters, yokes, shifter handles and etc. Most everything for T-5, Tremec or AOD conversions. :nice:
  5. M

    crossmember and shifter question...

    National Parts Depot lists in their catalog a crossmember for AOD conversion and a shift rod conversion to let you use your original shifter. _____________________________________________________ 70 Mach 1 351c FMX
  6. M

    Need some ideas

    Could you possibly use a torpedo style space heater and make an oven out of sheetmetal that the heater could blow into. Just an idea. ______________________________________ 70 Mach 1 351c FMX
  7. M

    wherer is my trans fluid leaking from?

    Another thing to check is the speedometer cable. Pull it out and check the o-ring seal. Also check cable itself to make sure there are no cuts or breaks in it near where it goes into transmission. _______________________________________________ 70 Mach 1 351c FMX
  8. M

    Intake Shopping

    Give this place a try in Louisville, Ky. The Mustang Store (502)964-2165 7 am - 7 pm Sat. 9-5 They part out a lot of mustangs and i remember seeing a bunch of 2v and 4v intakes on a shelf and more sitting around on the floor. Hope they have what you need. :)...
  9. M

    69/70 Owners, you too Pak

    I hope you can work something out with him. Sounds like a great find. There is an old guy near me in north central Ky. and he has eleven 69 and 70 mach 1s and fastbacks in a junkyard. He won't sell any cars or parts at all.Says he's going to start fixing them up for his grandkids. yeah...
  10. M

    PAK, decipher this one!

    You did great finding a Mach 1 under $2000. I gave $4800 for my 70 Mach 1 I just bought
  11. M

    PAK, decipher this one!

    Here's a photo of a Lime Gold 69 Mach 1 http://www.svs.com/users/zim/mustang/images/69-I.jpg
  12. M

    Will a 9 inch rear from a 68 Ranchero bolt up to my 67?

    There is a rearend dimension chart in the July issue of Mustang and Fords magazine. It shows the flange to flange dimension the same at 59.375". the spring pads are 43" centerline to centerline for the mustang as previously mentioned. For the Ranchero spring pads are 41.25" centerline to...
  13. M

    1970 Mach 1 Hood?

    It's your car. Go for It! I like the blacked out hoods on the 69s too.
  14. M

    holley cfm formula?

    That formula gives you carburetor size for best throttle response, fuel mileage and driveability. On my previous 70 Mach 1, I used a Carter 625 and loved the way it made my car perform. It had a Holley 600 on it but changing to the Carter made a big difference in the way it ran. I am planning...
  15. M

    Rear ratio difference

    I did some calculations to figure engine RPMs for you.I don't know what the diameter of your rear tires are so I did the calculations using a 26" tall tire. At 55mph with 3.25 ratio engine RPMs are 2310 At 55mph with 3.50 ratio engine RPMs are 2487 At 65 mph with 3.25 ratio engine RPMs...
  16. M

    FMX to C6....Final Decision

    The C-6 should be a direct swap for the FMX. I just changed from a C-4 to FMX and had to change everything. I have a small block C-6 but it needs rebuilt and I found a good FMX for $100 so I put the FMX in my car. I found out that the C-6 and FMX are the same length so driveshaft used is the...
  17. M

    what exhaust to put on

    This system is always for sale on Ebay. It comes with an H-pipe to fit the Tri-y headers or stock manifolds or HiPo manifolds, depending on which one you want. It does not give pipe size but says it will work with the GT extensions. All aluminized with turbo mufflers. They have a phone number...
  18. M

    351c Valley Pan

    What is the purpose of the valley pan under the intake manifold on the 351c engines? Does it have to be used or can it be deleted and just a gasket set used in it's place. Thanks.
  19. M

    Wheel Questions???

    Bolt pattern is 5 x 4 1/2" circle. Not totally sure on backspacing but should be about 4" to 4 1/4".
  20. M

    O.K. forget fixing the FMX. Will a C4 bolt up the same?

    I bought my car with a bad C-4 in it. The C-4 can't handle a cleveland in stock form. It has to be built up inside. THen they will handle about 400 to 450 horsepower reliably. The one advantage is that the C-4 is smaller and lighter with less internal mass to turn so there is a gain in rear...
Top Bottom
Back
Forums
Menu