Search results

  1. onefaststang

    2007 3v cam options

    New vct solenoid and shes running like a top. I am very impressed with how it runs with the xfi stage 1 cams. Seems like it just doesn't want to stop pulling. Feels about the same as it did before down low. No noticable loss. Car runs fine with no tune. I'm sure we could pick up a lot more...
  2. onefaststang

    2007 3v cam options

    Looks like I have a sticking vct solenoid. Put 12v to it with the power probe and it smoothed back out.
  3. onefaststang

    2007 3v cam options

    Cams did not solve the problem. Car seemed to run great until I got about a mile away then it started missing again.
  4. onefaststang

    2007 3v cam options

    Cams are in. Idles like factory, at least very close. I believe the LH cam has been changed before. There was black silicone one one side and grey on the other. Passenger side cam shows wear, but none what so ever on driver side. I will drive it tomorrow and see how it runs.
  5. onefaststang

    2007 3v cam options

    I ordered the xfi stage 1s today. She doesn't need anything crazy. Only thing I need to get now is new phaser bolts. Going to see what happens without the tuner. If necessary I'll order a tuner afterwards. I'm not doing this to build her a drag car, so I'm not looking for every extra hp...
  6. onefaststang

    2007 3v cam options

    Car has a cdc shaker on it. Cai won't do much good wirth that system. I would rather keep some low end torque, like I said it's my wife's car. I will look into the 127050's. Comp cams says no tune required? Even the 127200 they say no tune required but summit says tune is required.
  7. onefaststang

    2007 3v cam options

    I dont have a problem getting an sct, or whatever is used now on these. This will is the first 3 valve I have been in but it looks fairly simple so far. The car already has the JBA headers, so they are staying. Car has about 130k on it actually. I will look into the delete plates.
  8. onefaststang

    2007 3v cam options

    Wife has a 2007 GT. Car had a slight miss before putting it away for the winter. Well it's time to get it out again, so I did plugs and it was still missing. Put a set of coils on it, still missing. Pulled the valve covers and she has a cam lobe that is wiped out. Are the FRPP hot rod cams...
  9. onefaststang

    Ccrm Issue

    Coming back to this issue. I eventually changed the coil packs. Put a set of live wires coils in it and it imediatly cleared up. Car ran great for about a month. Took it on a 3 hour drive to Carlisle and it never skipped a beat. The next day i ran to the store and it started acting up...
  10. onefaststang

    Ccrm Issue

  11. onefaststang

    Ccrm Issue

    This was on the low voltage side
  12. onefaststang

    Ccrm Issue

    Ok. Got myself a noid light set. Put it in line with #8 plug wire. I then grounded my test light and probed the side of the coil plug the goes to that cylinder. After probing for a few seconds it seems to drop a cylinder or 2. There is still action at the noid light though. The flash seems...
  13. onefaststang

    Ccrm Issue

    Can I use a standard test light to do this? From all the actual noid test kits I have looked at, nothing is made for that specific application.
  14. onefaststang

    Ccrm Issue

    Absolutely. I can't track down what the problem is. I have done what I think I can do. If I can't straighten out out I don't know what I'm going to do with it. You can email it to me if you want to keep it private. [email protected]
  15. onefaststang

    Ccrm Issue

    No codes. How do I test for excessive dwell? I can email the video of my test, but have no way to post it here. Power probe grounded direct to battery. Also have new 1/0 welding cable grounds from battery to engine, engine to frame.
  16. onefaststang

    Ccrm Issue

    After putting the ecm back in I hadn't had any problems for a few days. Got daring and decided to take it to work this morning. On the way down the highway it started to miss again. It lasted for about a 1/4 mile, then cleared up. My wideband showed the a/f lean @ 18:1. That's as high as...
  17. onefaststang

    Ccrm Issue

    Put the power probe to the connector at the coil. I have power to the center pin but it is not 100% constant. It flashes. The 2 outside pins also have power, but it drops every few seconds. I have video, but no way to post it.
  18. onefaststang

    Ccrm Issue

    Pulled the pcm and opened it up. Can't find anything. No burn marks, no loose soldier joints. Looks like I'm pulling the loom off and tracing some wires.
  19. onefaststang

    Ccrm Issue

    Absolutely. Pm coming your way.
  20. onefaststang

    Ccrm Issue

    I'm guessing it's not as simple as just swapping it with another due to the pats?