Search results

I am frustrated - I just had a new centerforce dual friction clutch installed with a new pressure plate, t.o.b. and resurfaced flywheel less than 2k miles ago on my 1993 5.0 in my 1970 mustang because the throwout bearing was squeeling. Now the throwout bearing started squeeling again in a few...

My factory air stopped working today - when I looked under the hood and cycled the air conditioner on and off the clutch tried to engage but the rubber part has been split all around the middle section. I was able to spin the center shaft by hand with the engine off and it seems that the...

I have a recent ticking under the valve covers and have pulled them off - all the rockers appear snug BUT I need to know what is the proper torque for these 1.7 factory ford COBRA roller rocker arms made by Crane Cams so I can shut the ticking up. - Any other suggestions as to what would cause...

California car purchased from original family and garage kept. VIN is 0F02Fxxxxxx - VERY clean - original floors, quarters, rails, aprons... no rust or accident problems. Fuel injected computerized 1993 5.0 Mustang GT engine with 1.7 roller rockers, freshend with new bearings, balancer, oil...

93 5.0 almost stock - sounds like p/s pump but I don't think it is - that does make some noise at times too though. Happens all the time - even when not moving or not turning the steering wheel. At idle it is not bad - when revved it gets louder even while sitting still. When the clutch is...

What would cause an intermittant pop when turning nearly full over left at low speed. It "feels" like it might be a strut. Would a strut make a pop when turning sometimes or could the steering rack be bad inside? I checked the ball joints and tie rod ends - no "play" and I lubed all grease...

Will loose 1.7 Crane roller rockers cause a random missing while driving at 1500rpm or so with light pedal pressure just keeping up with traffic? I have cleared ALL codes and re-checked that they were gone for good, changed coil, maf, distributer, ignition module, cap, rotor, plugs, wires, O2's...

1970 w/ 5.0 FI, negative camber wedge kit with dropped upper control arms by 1 3/4 inches, all NEW control arms, bushings, tie rods, heavy duty front and rear sway bars, Granada disc brakes, etc... 9k miles ago when restored. Car has NEVER been hit - rust FREE garaged kept 302 2v California car...

Anybody else have this problem? I have had both Steeda Tri-ax and Pro 5.0 shifters on a couple of 5spds and both were hard to put in first gear when sitting stopped at a red light. New pilot bearing, new throwout bearing, new Centerforce Dual friction clutch, resurfaced flywheel, professionally...

1993 GT convertible - Slow speed in driveway - 5spd - all rebuilt 5k miles ago w/ new Centerforce dual-friction clutch, rebuilt rear end with extra posi clutches, etc... I checked U-joints by wiggling - no play, motor mounts - tight and no cracks, trans mount tight and no cracks and attaching...

I was at a swap meet and looking for aluminum heads and found a deal on some AFR's with 1.7 Crane roller rockers - they looked great but I noticed a wear pattern on the roller rocker tips at the valves where some were exactly in the middle of the roller like I would expect and several were no...

I am told that it is not available but I find it hard to believe that the most popular rear end on the planet has no rebuild kit available

Why? Just noticed it yesterday turning into a parking lot at 10 mph with no stereo on. This only occurs when turning LEFT on a fairly tight turn - normal turns in the road it does not do it but turning a corner into a parking lot does it. It sounds like it is coming from the rear end - checked...

I have a cold air kit on my 1993 GT that puts the round 7" or so tall high flow filter inside the fender area. I have NEVER had a problem with this set up until today. I was driving for hours in fairly heavy rain and the car started randomly bucking every so often - sometimes worse than others...

I have a worn gear and am trying to find out which it is--- Tranny tag reads f0zr-7003-aa rep-av 13-52-199 89369g2413 -- the gear in question was next to the last gear on the tailshaft set of gears -- it has 32 teeth that are NOT angled but have a "v" shape on one edge that has worn...

Anybody know what the part number is for the input bearing and race for the 5spd that is not included in the 94 piece rebuild kit from Ford Motorsport? Or where can it be bought - local auto parts store?

I have searched - My E303 w/ 1.7's feels wimpy off idle but comes on strong after several hundred RPM's - I miss the low end pull of the stock cam w/ 1.7's right off idle. I read advancing the E303 cam by as much as 6* will increase low end punch off idle --- BUT how much? What can I expect to...

What items need to have a CARB or EO number to be completely legal on a 87-93 5.0? -- No wink, wink - nudge, nudge pass stuff - just technical REAL good to go with no concerns. -- Cold air kit? MAF? Throttle body? EGR spacer? Intake manifold? Valve springs? Lifters? Rocker arms? Headers...

I have put some Slick 50 High mileage ATF treatment (thick goo) in my gear case to try to quiet it down but still has this rumbling noise when in neutral with my foot off the clutch and when under power in 2nd and 3rd gear - easy or hard - stays the same - no other gears make noise. Seems to...

Will the stock automatic computer properly control the engine for high performance use since it has been changed over to a 5spd - car runs good but I wonder if it is to blame for the car feeling sluggish compared to my other A9L 1993 GT setup. I have heard that the A9P automatic computer can...