Search results

hey what size belt did u use when you deleted the A/c. I saw you use a 47" and it didnt work way to small?

If i go with the et streets rear with it be bad to mix them with my skinny radial fronts?? people told me that its bad to mix them. plus i have no swaybars front or rear.

my suspension is stock other than the uppers and lower in the rear which are the upr ones with the hem joint style. I know i need to do some more stuff like prob a k-member with coilovers and new springs and shocks in the rear. just thought it would of hooked up a little better but looks like i...

ok thanks guys yea i will prob run the drag tire since the car is not streetable. do you guys think i should go to a 28" tall tire or stay with the 26"

im launching around 3000-4000 and side steppin the clutch and floor it and the nitrous hits. i tried to launch at 2000 and it falls on its face i cant slip my clutch its either on or off it grabs too hard. so i have no clue what to do?

I have mickey thomson et street radials on weld draglites 15". I cant get them to hook up. I run them at 15-18 psi. Do a 2nd gear brunout and heat them up good. But i think im going to ditch them and run just ET streets. I have a few questions, Do i have to run a tube in them? And if i do have...

here is a couple of pictures of my launches

The guy that tuned my car the first time said everything was ok didnt need anything. But when he tuned it the nitrous pressure was only 700 psi. I didnt have a bottle heater at the time. Since then i got one and i asked him when i do get full bottle pressure will everything be ok he said yea...

well i took out the eibach springs and have the stock ones in there. i havent took it off my sig yet. the nitrous comes in at full throttle and has to be after 3000 rpm. yea but i think im going to need some more suspension mods. im going to be getting a k-member with the adj coil overs. so i...

Well my problem is im drag racing my car and i cant get the dam thing to hook up. I got weld draglites and mickey et streets 275. i just purchased a set of upr soild adj upper and lower control arms and it still wont hook up. My 60fts are 2.0 cant get them lower. I have the rearend with moser 31...

i just installed one myself and it was farily easy other than removing the brake lines and installing the new ones. Ford gives you no room to work. But other than that works great

i run a 125 shot and no problems. It turns on at 3000 rpm and the timing is retarted 6 deg to be safe. just have it dyno tuned and ull be fine :D

Im going to be 80 percent of the time dragracing and going to be dumping the clutch at high rpm with mickey et streets. Which differental should i buy? I want something thats going to take that abuse. I called detroit they said the tru track should be ok they have 9 second cars running them but...

if it isnt that then check ur driveshaft u-joints and slip and hope it isnt ur pilot bearing or throwout bearing or u will be pulling that tranny again :eek: i would just get the mms adj quadrent and pedal pickup. The stock one is plastic crap so u cant go wrong with getting one. Dont go...

I was installing my new clutch and flywheel and i stripped one bolt into the crank. :bang:Well like a idiot wasnt paying attention thought the new bolts they give u with the flywheel where the ones for the crank. Started to tighten one down and it started to strip and once i saw that i pulled...

the thud could be the clutch not letting all the way out. and it grabs as ur hitting the gas and a thud. do you have a adjustable clutch quadrent? if you dont i would invest in one so u can adjust the clutch so it not so tight. that could be your problem. If you dont have one go with maximum...

thanks guys. i have a eibach spacer in the rear it might be like 1"1/4 i forget lol but that might work for the front when i take them off the rear. As for tires i want to run a micky et street drag radial. for the front i dont care w/e fits

I have a 2003 mustang Gt which im going to be putting some skinnys on the front and slicks for the rear. Now which backspace should i go with on each set? What tire sizes should i use for the front and back?

i looked at your garage and your exhaust is stock with weld in flowmasters. I think you need to change mid pipe and cat bad to 2 1/2 inch pipe. The flowmasters dont really give you any power i would go with the magnaflow. I got a throttle body and the upper plenem.

Well when i was looking for cams i didnt know what to go with. I asked on here and the one that got me on the vts where HOTMUSTANG. He did a big write up of his cam swap. I almost was goign to get comp beacause of Vts back up orders. I placed my order in january and didnt recieve them untill...