Search results

This is a 04 grand marquis 4.6l same motor The throtttle body has 2 vacume lines on it,1 is about 1/2 inch closest to the end of t/b It goes into some type of selenoid on the pass side of fire wall w/a quick connect and turns into hard plastic tubing right there. Other wise its 1/2 inch rubber...

Will the tranny still mount properly with out the inspection plate? My buddy threw his out and now were stuck w.out it.

My rear brakes dont do squat unless I pull up my e brake and jam them hard. Someome told me its because there not adjusted right with the ebrake cable spring? or something Can someone tell me what s that about? the brakes are all new and should work.

I need some help diagnosing these symptoms Starts off as as awhine at high speed 70-80mhp but only when i let off the gas Going around around a huge turn the whine is pretty loud on or off the gas Jacking one rear tire up///I heard a click like the axle snapped outward a little ...as...

How much pinion angle will a doublecardan joint make up for in the rear? IM having a problem setting my pinion angle with only being able to move the tranny up/down..The driveshaft specialist put a double cardan on and IM still getting vibrations up top 80mph verry bad when i piish the clutch...

I have a victor efi it says 4000to8000 rpms now whats suppose to happen beneath 4k? I have sluggish power beneath and its aggrivating. My question is...are these made for racing only? when i get to 3k rpms the car starts to come together real sweet and it pulls wayyy into the red zone...

http://www.corral.net/forums/showthread.php?t=811871

help!! where does this white wire goto? and the wires on the coil get tapped into? Also the coil has a red AND red/grn stripe as power,which gets used? anyone know where to get the switched 12v from? please be specific,the msd instructions dont help me at all.

I need to know which wires do what on the harness,im using a pih kit and having fan issue if u have a diagram email it to [email protected] please

I need some input. xe282hr cam dometop 11.5.1 vic efi intake rpm 202s long tubes stock balancer. billet flywheel,dual centerforce moroso drag pan,main girdle etc etc The engine revs smooth as silk up 3500 plenty power exactly 3500 it starts vibrating and smooths out a little as...

I mean its pretty smooth untill you get into a nice acceleration/load It dont feel like somethings grinding or whining. Just vibrating. And here and there I hear some loose clanks and/or strange sounds from the tail. Is aLLthis normal? And these trans dont like to be speed shifted at low...

I just got done doing a aode to tko swap . Im having a vibration while the cars on the lift,as soon as i let out the clutch it sometimes makes a grind sound,AND THE REAR BOUNCES UPWARD,kinda feels like the u joints are binding. But it dont do it all the time. I drove the car,and it goes...

I already put the darn thing on and didnt concern myself with the numbers for the timing. now i dont know what to do? I need advice on setting the dizzy to tdc and stuff too

I have a single wire alt and I cant find anything on the alt harness and what wires are for what"on the 95 marness" anyone have wisdom?

306 dometop kb pistons 11:5:1 compression 202 edelbrock heads 60cc xe282hr cam vic 5.0 efi intake eagle sir rods fms flywheel 1.6 rockers plus all the accomodations of top grade fuel system and ignition stuff and t/b,maf,long tubes,all that stuff. im guessing 400crank hp and a...

I need a 5pd tranny harness to use my tko in my aode car swap. Ill buy it new /used whatever or if someone feels like donating one thats good too. I just need some direction here guys. Thanks dan [email protected]

I have te performance harness to use the a9l computer from fox but i need to use the tfi setup also,what do i need to do?

I had this setup already start before. I didnt put it together the 1st time,and the pushrods got bent pretty good. like 3 bent and 3 warped. anyhow I changed the pushrods. I think I did them right. I did it by instructions from crane cam..which was. exhaust starting to open...adjust...

Ok Im trying to adjust some 1.7 rockers and push rods The motor has a b cam First of all theres no freegin timing arrow on the damper. I found tdc compression stroke on num 1 cylinder After that intake/exhaust closed the next valve to open was the 3 exhaust and 7 intake. wtf? I...

I actually have a motor from i dont know what...i think its 91? it has 9e?? heads b cam 1.7 roller rockers the old owner bent the old pushrods by tightning them wrong,and im trying to figure out what pushrods to use. i was going to put stock rockers on..but the roller rockers are stud...