Search results

  1. CATMACH

    I need a clutch - QUESTIONS

    With the Spec stage 2 I have had the above problems along with the chatter. The clutch does not slip though. I miss my stock clutch.
  2. CATMACH

    how do i adjust my new clutch?

    Its the Did you loosen the set screw on the adjuster? Did you looser the jam nut? It might help pulling back on the cable when you turn the adjuster. About the pedal height, the only thing I know of is the MM kit that will lower it. Hope that helps.
  3. CATMACH

    how do i adjust my new clutch?

    I dont know anything about your triple hook. It sounds like they set your firewall adjuter out too much. A good starting point is about 1/4 inch out. To lower the release point, turn the adjuster clockwise or in (towards the firewall) but be careful not to turn it too much or your cable will be...
  4. CATMACH

    Need some advice on tires please...

    285's will fit a 9 fine but it doesn't seem like a good idea on the front. I had BFG KDW 285's on 9 rears and the bulge a bit. 265 or 275 on an 18x9 is plenty wide for the front.
  5. CATMACH

    Mach 1 opinions wanted

    The stripes might be ok, but I dont think the spoiler would be. I have seen silver and gold before and they looked good. The gold was like an old GT 350H. Didn't some of the 69/70 black Machs have red stripes?
  6. CATMACH

    Help me lower my clutch pedal before I sell my car :(

    Sound like you need a firewall adjuster as your clutch is releasing low. I would look at the kit from UPR. It has 3 screws to hold it on the firewall all the other kits I have seen have one. You can lock it in place with a set screw or jam nut once you get it adjusted right. I wold not recoment...
  7. CATMACH

    Mach 1 Mach 1's w/ aftermarket wheels!!

    These are for sale
  8. CATMACH

    car's in shop for new clutch!

    Pedal feel is a little stiffer but nothing you wont get used to in a few days.
  9. CATMACH

    car's in shop for new clutch!

    I have one on my Mach. It was noisy for a while but not now with about 900 miles on it. Just remember to take it easy for the first 500 miles.
  10. CATMACH

    tire questions

    I have 285/40 17 KDW's and no complaints although they are a little pricey. No probems with grip in the rain especially with t/c. Mine are the orig. tread.
  11. CATMACH

    looking for Rear window louvers for 99 and newer GT

    www.visuslouvers.com/mustangrear.htm Try there thats where a lot of Mach 1 guys are getting them from.
  12. CATMACH

    Does anybody know the answer?

    Sounds like crappy mil's other people have had the same problem. A predator hand held tuner can turn off the rear 02's, maybe others can too.
  13. CATMACH

    this is shady!!!!!!!!!!!

    Get your $ back that is b.s.
  14. CATMACH

    Blown 5.0 Cammer?

    Just remember 11:1 compression on that cammer. Also, the crate engine in the FRPP has a single throttle body.
  15. CATMACH

    Longtubes ?????

    People have used BBK 01 long tubes on our cars and they fit even though the exhaust ports are slghtly different shapes. Not for sure about MAC.
  16. CATMACH

    ADVICE NEEDED: Need to put in new engine

    What are your goals for the car? Are you just looking at getting it running? N/A or F/I? What do you want to spend? If I were to stay n/a I would look at a swap to an 01 Cobra 4v crate engine from FRPP. About $6000 you get eng,trans, elec. everything you need. I know you said motor only but I...
  17. CATMACH

    is there a differance between 32v and 16v bottom ends

    My Mach hits the rev limiter just after 7000. I think its 7050. Autos have a lower limit, about the same as GT's I think.
  18. CATMACH

    Mach 1 Mach 1's w/ aftermarket wheels!!

    See my avatar for a real crappy pic of my Halibrands
  19. CATMACH

    any complaints about the SLP setup??

    With a stock h it sounds great. Put a o/r x on there and uhh.. not my cup of tea. The quality is excellent.
  20. CATMACH

    Who here is from Indiana?

    Yeah that was me. I was back up there today and heard something about another dyno day in November, you should try to make it out. see ya. :cheers:
Top Bottom
Back
Forums
Menu