Search results

Hey guys. Been a while since I've checked in. Great to see a lot of the old guys on here, and plenty of activity. Anyway, here's my issue. When I take a right hand turn or shift lanes with a fair amount of load, I hear a cluncking sound. I don't hear it if the turn is pretty soft, and...

I've got a question about my fuel injectors. I'm going with a 347 stroker setup, and I'm wondering whether my current injectors will still cut it. Here's what's changing from the sig below. I blew my stock block, so I am getting a 347 stroker with a custom cam, upgraded springs and track...

Both bolts fell out on one side. What type of bolt should I use to replace? (grade 8 or other?) Also, what size? Last question. What should I torque the new bolt/nut to? Thanks for the help.

My BBK long tube headers seem to be dinging up against my steering shaft. It only happens in reverse. Maybe I'm getting contact somewhere else, but I suspect it's the steering shaft. Any suggestions on how to get a little more clearance? Any aftermarket shafts clear it up? I'd rather not...

Hey guys, I just got a Tremec TKO500 from Steeda installed. Anyone know how best to correct the speedo. I'm running 3.73 gears. Thanks.

OK, I'm having some major work done. Here's the issue I'm looking at right now. The bearing retainer (this part) was bent when i broke my crank. Or maybe it was bent when the shop was removing the motor. Whatever, it was bent. So they ordered a replacement. Problem is, I think they got...

I'm lookng at a Zoom aluminum flywheel for my newly built 347 stroker. I'm also going with a new clutch (Centerforce dual friction). Here's the one: Zoom 60-3104 - Zoom Lightweight Aluminum Flywheels - summitracing.com Anyone have any experience with Zoom or know about them? Is this a good...

I have a '94 GT convertible, with a strut bar from Maximum Motorsports. The strut bar works around most intakes. But I'm wondering about the hood clearance. Does anyone know whether it will fit?

OK, I killed my block. So I'm rebuilding with a 347 and custom cam from Jay Allen. Otherwise, my mods will essentially be the same as listed in sig. The question is, should I dump the Street Heat intake? My alternates are to go to the Track Heat or Holley Systemax. I've gotten two...

Got a recommendation to them. Just wanted to see if anyone has experience with them.

Could someone explain the basic benefits of having a machine shop balance an engine? Is there any benefit of having a short block balanced to the clutch and flywheel?

I killed my block. Hopefully I can salvage the heads, rest of my top end should be fine (mods in sig). So now I'm looking at rebuilding with a Coast High Performance 347 Street Fighter. Any thoughts? I was making about 285 HP at the rear wheels with my mods. I'd like to not blow past a...

OK, so I'm running to the store last night. Car's just warming up. So I'm not pushing it hard. Accelerating from the light, and I hear a loud bang from the engine compartment. A good puff of smoke follows, and the car goes absolutely silent. I coast off to the side of the road, bleeding...

At first, this looked like a pretty dumb idea. But check out the flicker slideshow. There is some crazy stuff they are doing in this buildup. The wooden wheels are a cool touch. BTW, have you ever seen headers that route the exhaust out the center like that? (side mounted blowers FTW!)...

http://www.youtube.com/watch?v=mwDy3lTxX8Y&eurl=http%3A%2F%2Fwww%2Edpccars%2Ecom%2Fcar%2Dvideos%2F06%2D03%2D07page%2DComedian%2Don%2Drice%2Dcars%2Ehtm

A couple of weeks ago, my serpentine belt bit it. It came partially off and got quite chewed up. I knew immediately something was wrong because the power steering went out. Well, I thought it was because I was using a belt that was just a bit too short, and the tensioner was past spec (and I...

http://onemansblog.com/2007/02/07/10-worst-drivers-ever-caught-on-video/

Looks like some kind of ice block fell out of the sky on this guy's Mustang. http://www.firstcoastnews.com/news/florida/news-article.aspx?storyid=74596 http://www.tampabays10.com/news/local/article.aspx?storyid=48194

I am on borrowed time with my clutch (engages in the last 1/8 or pedal swing). So I probably need to do that this winter. Anyone had a shop do their install lately, and care to share how much it ran you? I do plan on doing it myself, but just curious what a shop might charge. Labor alone...

Does anyone know the bolt size for the connector between the cat back and the mid pipe? One of mine fell out, and I'd like to run to the parts store and get it.