Search results

  1. BlownFiveLiter

    Engine Check Engine Light

    Does it have any codes when you check them?
  2. BlownFiveLiter

    Clutch Installation

    I suppose the biggest question is whether you're doing the clutch installation yourself? It's not an overly difficult job, though it is labor intensive and time consuming. On a mostly-stock car, you don't need something like a Centerforce Dual Friction that can handle a ton of power. My...
  3. BlownFiveLiter

    96 Cobra Trouble

    What codes do you specifically have?
  4. BlownFiveLiter

    What To Look For On Used S Trim

    It shouldn't have any effect, unless the cause of the engine failure was the blower coming apart. Check for a free turning shaft with no free play. The impeller shouldn't appear to have any nicks in it, and should not come into contact with the housing at all. I wouldn't worry if it has any...
  5. BlownFiveLiter

    5.0 A Trim From A Lincoln Lsc, Fit On 88 Notch

    I swore the same, except that they were HO engines. It's been probably fifteen years since I've had the opportunity to look under the hood of one though.
  6. BlownFiveLiter

    94 Gt Need Help!! Car Won't Start Unless Ether Is Sprayed :(

    Bad PIP in your distributor. I'd put money on it if I were a betting man. Have anyone with a 94-95 that you could swap distributors with for half an hour?
  7. BlownFiveLiter

    Expired Feeler: '08 Bullitt #4862 E-force Supercharger

    Beautiful car! I can't blame you for considering it, with a 6 month old. I have a 2 week old and while my Mustang is hanging around, I think I'm going to sacrifice my two-wheeled toy (ZX6R). Good luck with the sale!
  8. BlownFiveLiter

    Exhaust Header Gasket Question

    I second this. Make sure to get a quality gasket that isn't paper-based. Ideally, a copper gasket is the way to go, but I've done well by the Felpro 1415 gaskets.
  9. BlownFiveLiter

    Tapatalk

    I'm just here because I heard there was pizza?
  10. BlownFiveLiter

    I'm A Dad!

    Very cool! Congratulations are in order for you, too! :nice:
  11. BlownFiveLiter

    I'm A Dad!

    Thanks guys! Another pic, after getting all cleaned up.
  12. BlownFiveLiter

    I'm A Dad!

    The car fund dried up a couple years ago. That's part of why I'm back in college at 32, so I can afford things again. Alex is a very welcome kick in the pants to get me to do it, too!
  13. BlownFiveLiter

    Engine New Here, Need Quick Information.

    Pick up a complete engine. You'd have more invested in machine work on the bad engine than you could likely pick up a used engine for.
  14. BlownFiveLiter

    I'm A Dad!

    Alexander Luu Nelson. 7lb. 7oz, 20 inches long. Born at 4:09 PM today.
  15. BlownFiveLiter

    Erratic Idle Surge After Warm Up

    http://www.stangnet.com/mustang-forums/threads/help-me-create-the-surging-idle-checklist.698148/
  16. BlownFiveLiter

    Heating Controls And A Carputer

    I don't know how good you are with coding and electronics, but I would bet you could do something like you're planning with an arduino unit for the climate controls. The easiest way to do it would probably to retain the factory controls and use a servo on them, controlled by the arduino, or the...
  17. BlownFiveLiter

    Vinyl Wrap Instead Of Paint.

    No Maaco/Earl Scheib places around there, Kurt? I'm sure you could do the prep yourself and drop it off for them after taping it off/removing trim. If the prep is good, a base/clear job is easy to spray, even for a place like that. It'd turn out decent, I'm sure.
  18. BlownFiveLiter

    Fuel 95 Gt - Issues Draining The Fuel Tank

    Just bite the bullet and pull the tank. Once you get the fill tube out, you'll probably get some drainage from it. When the tank is down, you can lift it and pour it into something. I used a bucket once. You will most likely take a bath in it, but it is the fastest way.
  19. BlownFiveLiter

    Electrical Noob Needs Help...

    If you get too concerned about how much amperage you'll be drawing, add a relay and run the stuff you're planning to add off of that.
  20. BlownFiveLiter

    Go Right Now And Check Your Distributor Cap Adapter Screws!

    Mike's rubbing in his distributorless ignition that the 4.6 has. Maybe I'll convert to EDIS on my 302? Hmm...