Search results

  1. B

    Washing the Engine Bay?

    Simple Green has been through Department of Defense (DOD) testing and was determined to be highly corrosive on aircraft aluminum and also a catalyst for Hydrogen Embrittlement in high strength aircraft alloys. I've been using Simple Green Extreme Aircraft cleaner.
  2. B

    C&L Intake manifold

    Check out this thread. http://forums.stangnet.com/783826-c-l-intake-manifold.html
  3. B

    any news on FAST intake

    This is the latest info from the PRI show. The manifold was dyno'd and produced 22hp on a stock 3-valve Mustang engine (forgot to ask if it was a chassis dyno or engine dyno). However, the added runner volume was excessive and pushed the powerband too high up despite the added runner length...
  4. B

    New B&M Auto Shifter

    The design team must like Tootsie Pops. It looks like a junior high school shop project gone bad.
  5. B

    2005-06 Mustang gt StreetFighter Torque Converter

    It's a stock long block with just bolt ons. The CAI is a one of a kind that I made, Jet TB spacer, CMRC deletes, Steeda U/D damper, Meziere water pump, Hooker LT's X-pipe, and FRPP race mufflers. Zex nitrous kit. Prothane motor mounts. A Bamachips tune. An auto tranny with a TCI 3000 stall...
  6. B

    2005-06 Mustang gt StreetFighter Torque Converter

    I've got 4.10's. :D
  7. B

    2005-06 Mustang gt StreetFighter Torque Converter

    The converter has very good street manners. Easing into the throttle it feels just slightly looser than stock. Nail the throttle and your rear tires are up in smoke all the way through 1st.:D
  8. B

    2005-06 Mustang gt StreetFighter Torque Converter

    I have one. It's one of the best mods you can do if you like to drag race.
  9. B

    ? for those of you using NOS

    Have you actually had problems with a Zex kit or are you just spouting rumors like the rest. Myself and two friends use the Zex kit with no issues. You need to keep the nozzle a minimum of 6" from the throttle body. Having the nozzle too close will cause improper atomization of the fuel which...
  10. B

    Headers for cheap....

    Flowtech ceramic coated $245 @ Summit.
  11. B

    Aftermarket Intake Manifold

    Hogan's makes one. Only $3000.00
  12. B

    For those with Nitrous kits....

    Yes
  13. B

    For those with Nitrous kits....

    Here's a pic of mine. Bought at Radio Shack.
  14. B

    Fan switch install?

    It's marked on the bottom of the relay.
  15. B

    Fan switch install?

    If you ground pin #85 on either the high or low speed fan relays the fan will run.
  16. B

    High speed torque converter in 05/06 GT

    I got 4 tenths, but my car wasn't stock when I put it in.
  17. B

    BMR "Street" LCA installation question

    Here are the BMR LCA's. The left ends go to the rear mount. The right ends go to the chassis.
  18. B

    Control arms - poly or rod ends?

    The race ones will transfer much more noise from the rearend to the chassis. I bought the BMR LCA's with the poly on one end and the heim joint on the other. They're a little noisey but a good compromise.
  19. B

    Subframes anyone?

    you probably won't need them until you reach 400 RWHP. This chassis is plenty stiff. With 375 RWHP my best 60' is 1.57 with minimal suspension mods.
  20. B

    Ground Control Street Camber Plates

    Not too much to see is there.
Top Bottom
Back
Forums
Menu