Search results

I actually have done lots of research on this topic but haven't found my exact situation in my searches. I'm resto-modding my 67 and the previous person had undercoated right over rust and grease. I'm taking it down (just the frame, wheel wells, engine bay etc....no body panels) to bare metal...

Hello everyone! I am just beginning my restomod on my 67 coupe and have no idea which suspension to pick. I've researched extensively the different combinations and have narrowed it down to a few choices. I am looking for anyone with specific experience with each of these. Before throwing in a...

Looking for a set of aluminum heads for my 289. Preferably with a small combustion chamber around 58cc. Thanks!

Hey everyone, been a while since i've posted on here but I'm finally saving up enough to tackle the 11 year long dream of finally getting to build my car the way i want to. I know I've got a long road ahead but i was just wanting ideas from all who have more experience with this sort of stuff...

I realize that the Demon and Holley debate has gone on for years but I haven't seen much about the quick fuels. I have a speed demon 650 on my stang now but im not too crazy about it. Lots of tuning issues. I know the basic design of the quick fuels is a basic holley design but so is the...

Ok this might be a long one, depends how pissed i still am by the end of it. :Zip2: I just picked up a speed demon 650 (it was the remanufactured one). I took it apart and cleaned it up cuz i've heard about all the metal flakes floating around (see i've done my homework!) and put it on the...

Hey guys, a few years back i had a 4 speed toploader put in place of my 3 speed. The transmission is awesome, however i think that the tail of the 3 speed was a bit longer than the 4 and the yoke doesn't quite go as far in as it could. I'm guessing this is where my oil leak is coming from? Is...

Hey guys, just wanted to say thanks for all the help you guys give! Nothing but the best advice! Anyways, I was wanting to change out my u-joints and found searching on the internet for spicer u-joints almost impossible (as far as finding a part number for my application). I'm looking for a...

Ok opinions needed! I'm looking into getting an adjustable strut for my '67 and was trying to decide between the Streetortrack http://www.streetortrack.com/adjustable-strut-rods.asp or the RRS setup http://www.rrs-online.com/html/suspension.htm hopefully those are the right links. Has...

Hey guys, how hard is it to install a new oil pump and pan while the engine is still in the car? Is it important to change them? How bad (or good) was the original? What is the deal with all these high volume oil pumps? If you could recommend any brands that you've had success with that...

Anyone either found gaskets with the crossover block or come up with a crossover block of their own? I have the RPM (not the air gap) and am not interested in keeping the exhaust crossover but can't find any gaskets that have the crossover block in them. I'm thinking of cutting small pieces of...

My brain has nearly oozed out of my ear trying to figure this one out....I'll just list everything. Just recently changed fuel lines to 3/8 stainless, no leaks with fuel anywhere. New harmonic balancer, timing chain, timing cover, no oil leaks there. New edelbrock fuel pump putting out around...

Ok so the fuel lines are almost 40 years old....guess it's time to change them! I'm hoping that might be what's causing the overheating and pinging at cruising RPM's. The car was originally the "C" code engine (1967) with the 2 bbl. carb so im assuming its got pretty pathetic fuel lines on it...

Hey guys, i'll try to make this short. '67 with 289. Just installed new double roller timing chain, new chain cover, new harmonic balancer and thermostat. I flushed the block out, cleaned the radiator, water pump still works, adjusted the initial timing to 11 deg. and total timing to 36 deg...

Hey guys, brand new to the forum! Got a question for you guys. I've got a '67 with the deluxe interior (brushed aluminum) and was wondering how to install some autometer ultra-lite gauges in them. Im not much on ordering from JME or Haneline and spending $1000 for a dash insert so i figured i...