Search results

  1. S

    possible fried computer?

    hey guys i let my buddy use my car and it died so he jumped it. He hooked the battery cables up backwards and now the car doesn't wanna run. Its a 5spd with and auto computer in it and its pulling a tot(transmission oil temp) code which it never pulled before. Also its saying low voltage to the...
  2. S

    Rear Suspension Question

    Hey guys i currently have a set of south side lift bars on my car. Should i remove them if im going to be putting lakewood 50/50's with a drag spring in there?
  3. S

    Head Torque Question

    Hey guys i currently have a set of edelbrock heads that are fire ringed and have lockwire head gaskets. Edelbrock says to torque them down to 70-80ft lbs. Do you think this is enough considering im going to be running 12-15lbs of boost and possibly a small shot like 40 or so of nitrous?
  4. S

    S/C Question

    Hey guys I was looking into a ysi but it says clockwise rotation only. What does this mean will it still work on my car a 90 5.0?
  5. S

    What Lug Nuts?

    Hey guys i recently purchased a a set of weld drag lights for my car. I never got any lug nuts with them from the guy i bought them off. What size and kind of lug nuts do i need for a 90 5.0 4lug? Thanks.
  6. S

    T/B Problem

    Hey guys i just purchased a new accu-fab throttle body last year. And its starting to seize up. When i first start up the car and hit the gas its hard like its stuck but then it frees up. My previous throttle body did the same thing. Could this be from running the coolant through it?
  7. S

    Help Car shut off wont start

    hey guys just rebuilt my motor. Drove it about 1/4 mile and it just shut off and the tach went dead. Theres coolant leakin out. (i think from the head) I was wondering if maybe the heads werent torqued down enough because the heads are fire ringed but i am not using fire ringed head gaskets...
  8. S

    New Motor Mounts Now Have Problem

    HEy guys i took the motor out of my car to rebuild it when we put it back in with the new motor mounts the motor sits about 1.5-2 inches closer to the nose of the car and i cant get the fan in. Any ideas to what might cause this? Maybe i reversed the mounting plates the motor sits on?
  9. S

    Eibach Drag Spring Install

    Hey guys whats the best way to install the eibach drag springs in the front. By droping the A-arm is doesn't seem to bee enough room and they are pretty hard to compress with some sort of ratchet strap. Will spring compressor do the trick?
  10. S

    rim and tire question

    Hey guys i ended up gettin a set of weld wheels 15x3.5 and 15x10 for a real good price. Anyways the front runners have tires on them already and the rears need new tires. can i put the 26x10.5x15's i have now on my ten holes onto the 15x10's or will they be to small?
  11. S

    South Side Lift Bars and 50/50's?

    Hey guys i currently have a set of south side lift bars in my car. I also have a set of lakewood 50/50's kickin around. If i put the 50/50's in should i remove the lift bars or keep them in. let me know thanks.
  12. S

    My setup Help

    Ok im going to be building a 331 forged internals all that jazz with a compression ratio of 8.5-1 and 15lbs of boost from my s-trim for right now. Im thinking of going with one of the XFI comp cams or keeping my Wolverine 1190 cam, AFR185 heads, but on the intake im not to sure. Im not...
  13. S

    Quick question on setup

    Ok going to be building a 331 running 15-lbs of boost and put some juice on it like a 125 shot. compression is going to be around 8.5-1 is that to high or will it be fine? This is going to be built on a dart sportsman block. Also with the permormer heads i have now be to small still even if i...
  14. S

    2-Bolt + Main Girlde Question

    Hey guys how much HP will a 2-bolt with a maingirdle support anymore than 500? Cause my 302 puts down 473whp looking to go to a 331. Will a 2bolt with a main girdle be enough or do i have to go 4 bolt?
  15. S

    331 kit?

    Hey guys looking to build a 331 but who knows who makes a good kit? I have the block but who makes one of the better kits to buy that has the rods, pistons, crank all that good stuff?
  16. S

    car goes low 12's should be faster

    Hey guys runnin 12.3 @ 117 and 112. 60ft is 1.8, Any ways i dynod on a dyno jet at 473 rwhp. Anyways my set up is in my signiture. People are telling me i should be running low 11's to high 10's. Will putting 90/10's with eibach front drag springs and 50/50's with trick springs in the rear help...
  17. S

    Wet or Dry Kit for S/C

    Hey guys looking to put a little juice on the car. But i have a Vortech supercharger running 12lbs. I only want like a 50 shot so i dont overdue it. But do i want to get a wet system or a dry system to run with the S/C?
  18. S

    Mac Dumps not sure if i like them (Clip Inside)

    Tell me what you guys think. New Mac Dumpshttp://media.putfile.com/MVI-0236 Old Flow 40'shttp://media.putfile.com/stang123
  19. S

    Mains are gone what to do?

    Hey guys the main bearings in my motor are gone. Should i just replace them or should i go buy and explorer motor and put the explorer bottom end in? I hear they have a point more compression and that those motors really wake up with the mustang computer is that true? Anyways let me know what...
  20. S

    Explorer Motor

    What year explorers had the 5.0 motors in them?