Search results

  1. bleedingvayneAD

    Anyone with 4.10's or 4.30's get in here!!

    I have 4.30s in my DD with every bolt on and 295/35's out back and I am sooooo happy I didn't go with 4.10's!! The reason I say that is that I sometimes wish I had gone with 4.56's because it almost feels like I need a little more gears and I thank my lucky stars I was brave enough to go with...
  2. bleedingvayneAD

    SLP LT headers

    No prob! I wish I could speak from experience about the SLp headers (or any headers for that matter), but I'm trying my darndest to not buy headers as I HOPE to go turbo soon... Anywho, If you are already lowered with the prochamber and are not encountering any problems scraping with that...
  3. bleedingvayneAD

    SLP LT headers

    I've heard that they fit VERY well and are equally as nice as all the other high end brands. However, I also know that they hang lower than most of the other brands because of how long they are. Yet, if you go catless, then it shouldn't be as big of a clearance problem as the catted version...
  4. bleedingvayneAD

    05-07' Camber Bolts

    Nope, they were able to get it aligned without even doing that. Don't ask me how because I was so happy that I didn't even ask them how they did it!t
  5. bleedingvayneAD

    05-07' Camber Bolts

    I installed BMR's 1.5"/2" lowering springs on my car and did not even need the camber bolts to get it aligned properly!
  6. bleedingvayneAD

    Looking at Hoods, need advice

    None whatsoever with mine. It was painted just like the top and looks equally as nice. I was kind of curious as to how it was going to look without the hood liner, but it looks great!
  7. bleedingvayneAD

    Looking at Hoods, need advice

    Here are some more pics....
  8. bleedingvayneAD

    Looking at Hoods, need advice

    I have Cervini's Ram Air hood on my car and the body shop DID NOT have to do any extra block sanding or whatever to make it fit correctly. They also said that it was the nicest looking fiberglass hood that they've painted that has turned out so well.
  9. bleedingvayneAD

    AutMeter 9117 Tach Adapter for 2007 GT...need HELP!!!

    I have the same shift light and hooked it up EXACTLY like the raptor. And, just like you dd, I also set the tach to .5 to read like a 4 cylinder since it's only reading off of a single tach signal wire.
  10. bleedingvayneAD

    NEED MORE POWER 06 GT AUTO

    If you can tie your own shoes and wipe your own pooper, then your abilities as a mechanic far exceed those needed to install an intake.
  11. bleedingvayneAD

    10.5" Rim Question on an 07>>>

    With the right offset, anything will work. You'll need at least a 45 offset for it to sit flush.
  12. bleedingvayneAD

    403hp at rear wheels no super or turbo

    Maaaaaaaaaaaaaaaaaaaaan, why does this guy have to be from Wisconsin?????
  13. bleedingvayneAD

    Anyone put a shift light in the new stangs yet?

    That is the exact one I have in my car, except mine has a black housing. It hooks up JUST like the Raptor and the digital spedometer is very accurate. The LED shift lights are very bright -- there are 3 levels of brightness and the lowest level is sometimes too bright. You can program the...
  14. bleedingvayneAD

    Wheel/tire Size's

    I've got some 295/35s going on my 18x10s
  15. bleedingvayneAD

    4.30 users

    I went with 4.30s because they're only like 300 RPMs or whatever higher than the 4.10s. And, honestly, gas milage? It's a V8, and I didn't buy the car to even ever think about conserving gas. I'm VERY happy with my 4.30s and would never do anything less if I had to do it over again. Part of me...
  16. bleedingvayneAD

    imcos are in

    ooooooooooooooooooo, how much for the stingers?
  17. bleedingvayneAD

    imcos are in

    If your axlebacks are crooked, then you should try loosening the h-pipe and adjusting from there back.
  18. bleedingvayneAD

    4.30 users

    As you know, I have 4.30s. I got my gears from 50resto and had them installed at a place called Speed Inc. near Chicago. This place even used their own install kit along with Royal Purple fluid. Now, the box the gears came in does say M-4209-G430M, so they were made by Motive. I don't know if...
  19. bleedingvayneAD

    2005 mustang gt finshed all mods at last

    You won't come close to breaking the quickest N/A 1/4 time by a long shot...
  20. bleedingvayneAD

    Dyno results Underdrive pulleys

    Crap, just ordered the UDPs and BMR adj. panhard this morning. Not good, especially when you don't have the money for them!
Top Bottom
Back
Forums
Menu