Search results

Hey guys i have a 93 coupe, mods are as follows: 89 shortblock with gt40p heads exhaust TFS stage 1 cam holley AFPR Accel #24 injectors bbk CAI etc etc..... i put on a C&L MAF with the blue sampling tube for my #24 injectors. the cars drives and runs ok but under WOT around 3k it...

hey guys, i gotta 93 coupe and i recently put a 89 shortblock with 90k miles on it. i added gt40p heads and a holley systemax intake. i have full exhaust, 73mm C&L MAF and 70mm TB, and accel 24 LB injectors, msd coil, taylor wires, and autolite plugs. the car bucks under wot and pops. also the...

anyone have any ideas what is causing my hanging idle. after i rev it it comes down to 2k for a few seconds, then drops to about 1300..... the drops right down to 900 and idles smooth even with my TFS stage 1. any ideas?

hey guys i got a painless wiring thermostat kit for my new SPAL electric fan. i have a holley systemax intake. i dont see a second hole for the thermostat to thread into. any ideas? thanks!

hey guys, i gotta stewart warner water pump. it cam with two plates. i put the one in and it didnt look lke the other one was suppose to go behind it. the water pump needs to come out about 1/8 of an inch to align my pulleys. do i use both of the plates? thanks!

Hey guys, i have a 93 AOD coupe. I really am thinking about converting it to a t56. My friend has one he will sell me out of an 03 cobra, but its electric speedo... i was thinking about getting a kit from D&D and i just called them and they said there kits are only to go from a t5 to a t56. what...

Are there any roller rockers that will work out there with 99 explorer gt40p heads? i had the guideplates, 5/16x3/8 studs, and proform rockers. The rockers sat to high and were a little to far past the tip of the valve. Is there a company out there that makes a set??? thanks!

what is the point to running one? thanks!

I have a Flex a lite black magic fan and i wanted to wire it up tonight. where is the easiest and best place to splice the wires into? i have ac also. any help would be appreciated. thanks a lot!

OK guys i gotta 89 shortblock in my car with 90k miles. here is my setup: GT40-P heads from 99 explorer holley adj. fuel pressure regulator holley systemax intake EGR valve disconnected MAC headers, catless h pipe, flows BBK 70mm TB NEW frpp #19 inj. * deleted PCV and...

Ok guys, I got my motor ALL back together. go to start the car and hear a popping. notice the intake is a little loose so i tighten down a bolt a little more and broke a chunk of the upper intake right off :( i have ford racing valve covers which are obviously taller then stock ones and and the...

OK guys, i got my new shortblock in and everything pretty much done. now all thats left to do is bolt all the brackets and accessories back up along with putting on the water pump. well guess what...... i didnt pay much attention when taking this stuff off!! I really need pics of the accessories...

Hi guys, im putting in my new shortblock and just have a quick question about where the ground straps go... i know the one bolts to the bellhousing from the firewall but where do the other two go? thanks a lot!

Hey guys, im putting together a 89 302. i got a TFS stage 1 cam, GT40p heads, comp rocker arm studs, comp guidplates, and proform 1.6 roller rockers. when i put it together i noticed the pushrods are too short. what length do i need?!?! thanks!

Does anyone have a clip or vid? thanks!

hey guys, my motor is all ready to go together. i got a set of used gt40p heads off of a 99 explorer. I was wondering if anyone has the specs on these heads?! also i have Mac equal length shorty headers and i was wondering if they will work or will i have to get a different header? lastly, what...

im puggting together my stock shortblock with TFS stage 1 cam and gt 40 p heads... i was wondering what would be a good rocker to go with for this ecombo for the money? also specs on this cam are .499-.510... what would 1.7s bring this up to??? thanks!

Im getting ready to put my stock shortblock back together and im wondering what cam would be good to go with? im keeping stock e7s for a little bit...... would the x 303 be a good choice or a TFS stage 1? thanks guys :nice:

can someone please tell me where to hook up the coil wire for an autometer tach? also we have a tach adapter. i got into the main loom leading to the injectors and coil packs and there are 4 red wires. is one of them the one? any advice is appreciated! thanks!

Is there some way to get rid of the PVC valve to keep the intake cleaner?