Search results

I'm looking at buying a brand new Roush engine with a c6 built for 475 hp from a guy that needs the money. Here's the kicker, it's been sitting for 5 years. He said he goes out and turns the engine over by hand every now and then, but thats it. Is there anything else that need's to be done to...

This is a brand new Roush 342r that a guy needs to get ride of.I know a new one is about $12,000.I'm either looking to put this in my 66 fastback or sell it to make a few bucks. It's actually 3 years old but has never been run. Does anyone have an idea what something like this is worth.Thanks

Looking for a really good set of vent windows for my 66 fastback.I'm looking for some with no pitting and the chrome must be nice.I will even take one if it's really nice.Thanks

I have an Edelbrock carb on my car and I have a problem with it when I turn the car off the fuel keeps coming in for at least 15 to 20 seconds and then its flooded. There must be some kind of pressure issue.Does anyone know what the problem is? Thanks:shrug:

Looking for a nice 93 cobra with lower miles to trade for my 66 Fastback or sell the fastback. It's not quite all the way done but with be ready by spring at the latest. It was media blasted in the early 90's and was originally white. It has Baer brakes,comletely stainless steal exhaust, and I...

Will a t-45 out of a 98 cobra work on a 5.0? Thanks

I have an 86gt that I want to put a 94 and up rear end in so I have rear disc and 5 lug axles. Would this be a direct bolt in or is there some mods needed? Thanks

I have a 289 that I put stud mount roller rockers in and the cam I got is a Crane energizer hyd. cam(part #130052 at Summit) that has duration of 272 and a lift of.484(thats figured with stock rockers) I was trying to figure out what length push rod I need and I come up with about 7 1/2 inches...

Planning on putting the 2 white stripes down my 66 fastback.Was just wondering if anyone knew the correct width on them and how far apart they should be?Thanks

Does anyone know if a 18x 9 front and a 18x10 rear will fit on a 86GT?Thanks:shrug:

I have an 86Gt that needs a rear end installed.I want to put an 8.8 in instead of a 7.5. What years will work.Is it just through 93 of will the later years work? Also are they a direct bolt in? Thanks

I just had my 289 rebuilt and also installed a Crane hyd. cam and I also bought some 1.6 roller rockers to put on. When I set the roller rockers on, the push rods seam 1/8 of an inch to short at least. I'm not to sure how tight I need to tighten the rockers. It doesn't seam like I should have...

Looking for a set of 1.6 roller rockers for my 66 289.Thanks

looking for a set of heads that will on my 289, they need to be complete and ready to bolt on.Let me know if you have anything.Thanks:nice:

Looking for a set of complete heads to put on my 289.Looking for a little extra performance,I want something ready to bolt on.Thanks

I have a set of 302 heads that were just completly rebuilt.I want to put them on a 289, the heads are off a 74 302. Do the 302 heads flow much better,or not at all? Thanks:shrug:

I might buy some GT40P heads but I've heard that it's hard to find headers that will work.I have a set of tri-y's, does any one know if these will work? Thanks

Does anyone make a conversion kit for an 86? I see them for 87-93 stangs.What do I need?Thanks

What do you guys think is the best engine build is for a 289.I am rebuilding my 289 but want to upgrade the performance but not to crazy. I want to be around 300 hp. Not wanting to spend a ton of money either.Is there a engine kit that would get me around there.Please give me some ideas.Thanks

I have a 74 302 engine and I'm looking for a good set heads. What heads will work with this application. Thanks