Search results

  1. S

    uneven wheel/fender spacing pass vs driver side

    On the front suspension,the driver side wheel/tire comes flush to the edge of the fender lip but the passenger side wheel/tire is about an inch short from being flush with the edge of the fender. Im trying to figure out if something is off with the suspension or if the fender is off. I've got...
  2. S

    Gauge pods

    sold
  3. S

    H&R Race springs - REAR pair only

    sold
  4. S

    Front wheels spacing with fenders is off

    I'm confused on what is going on with my car. My front wheels spacing from the fender is off. The driver side wheel/tire sticks out flush to the fender edge. But the passenger side wheel/tire is about 1 inch inside the fender well. What in the world could be causing the spacing to be off. Car...
  5. S

    OEM steering wheel

    sold
  6. S

    any tips on putting a dimple in a header tube?

    Ive got ceramic coated bassani headers. There is a small spot i need to dimple a bit to clear my K member. Anybody have any tips on how to go about this? Ive heard heat it up with a torch and smack it with a ball peen hammer. But wont the torch kill the ceramic coating? Will the header tube...
  7. S

    Bassani header install help

    Anybody see anything wrong with the install on this passenger side front header tube? A shop did the install a few years ago, its touching the other header tube above it and now i cant install my tubular K member/motor mounts either, since its rubbing both of those on the bottom of the tube...
  8. S

    tubular K member/header issue

    Ive got Bassani mid length headers and just put in a tubular K member. The front header tube on the passenger side is up against the K member. the engine isnt even on the K member yet, its being supported about an inch above. I would imagine the rubbing only getting worse when i drop the engine...
  9. S

    Vortech V2 Si trim

    SOLD
  10. S

    which PCV valve to use for supercharged 2V engine

    Ive got a vortech S trim and running a oil catch can between the PCV valve and bullitt intake. Ive heard that you want to run a 2 way PCV valve so you dont have a boost leak or too much pressure in the crankcase. Supposedly the stock bullitt PCV wont do this since its only a 1 way valve. So what...
  11. S

    99-04 OEM Ford headlights

    OEM headlights are sold, but i have a pair of aftermarket lights for sale.
  12. S

    aftermarket E brake handle

    I was just looking around for an aftermarket E brake handle and ran across this MOMO handle. Anybody have it? Would it even work with our cars? 2002 Ford Mustang MOMO Pit Stop Hand Brake, Momo Emergency Brake Handle
  13. S

    leather shifter boot

    Anybody replaced the cheapy vinyl with a leather shift boot? I got the Ford Racing Cobra leather boot. Pulled off the old vinyl POS but you have to break off the mounting tabs to get it off. Now im wondering wtf i use to hold on the new leather boot to the bezel? Any suggestions from people...
  14. S

    gear oil

    I got 4.10's installed yesterday on my 2002. The shop put in 80w90 premium oil with friction modifier. But talking to a buddy, per the ford mustang manual, his 2000 says use 80w90 premium with friction modifier, but my 2002 says use 75w140 synthetic . Arent all the rear diffs on 99-04 the...
  15. S

    5th gear ping or just a rattle?

    I cant tell if its pinging or just a rattle. It doesnt always do it either, but when im on the highway and in 5th gear, and try accelerating from 50 or 60mph, it sounds just like pinging. but then it doesnt do it every time i drive the car even on the same tank of gas, so its kinda confusing...
  16. S

    4.10 gears with a centri supercharger

    Ive got 3.73 gears right now and it doesnt get me too boost rpm range quick enuf. But i'm afraid that 4.10 might be too much. Anybody have 4.10's with a centri supercharger? I'm running about 450rwhp and Nitto 305/35/18 drag radials.
  17. S

    intermittent rear diffential leak

    Kinda confused about this leak. It seems to only leak from this point where the driveshaft meets the rear differential IF ive had the car on jack stands or a jack at a steep inclined angle. (Like this weekend i was doing a fuel filter change and had the rear end raised quite a bit and it started...
  18. S

    pulling back on clutch pedal for adjustment

    Supposedly pulling back on the clutch pedal all the way until it clicks self adjusts the clutch engagement. Ive tried this a ton of times and pulling back on my clutch pedal does nothing. When my clutch pedal is in its resting position, thats as high as it goes. It doesnt pull out any farther or...
  19. S

    Clutch symptoms?

    Ive been having a wierd metal rattling sound coming from near the collector area of my headers for a couple months now. Never been able to pinpoint it. It also rattles when getting on the gas hard to where it almost sounds like pinging (but its not pinging). So today i was sitting at a stop...