Search results

  1. Saleen0679

    Interior and Upholstery Center Console E Brake Handle - Seal and Retaining Ring Failure

    A good RTV type adhesive will hold the seal on for decades.
  2. Saleen0679

    Looking for a hardware source

    ClipsAndFasteners.com autofastenersandclips.com
  3. Saleen0679

    SN95 Need wiring diagram for 3.8l 1994 Mustang GT Please!

  4. Saleen0679

    SN95 Need wiring diagram for 3.8l 1994 Mustang GT Please!

  5. Saleen0679

    Progress Thread Father Time: High-$ anti-dent defense system

    "Driver's side door-well above the kick panel area" - 9D843 - Cruise Control Module "A box hanging loose above the pedals" - Rear Window Defrost Control Relay - Should have 18C641 on it somewhere. "These mount on the brace between the door frame and the steering column bolts" - The olive box...
  6. Saleen0679

    Electrical Instrument Panel Light Dimmer Switch

    The old style is on the right. It is aluminum and has the coil rheostat. The newer style on the left is all plastic, shorter, and uses contact pads and a wiper as seen through the top.
  7. Saleen0679

    Electrical Instrument Panel Light Dimmer Switch

    The same thing happened to mine years ago. Seems to be a common problem. After taking a meter to my switch I assumed the rheostat coil was bad somewhere under that green adhesive. That green adhesive crumbled and left a powdery mess so I tossed mine and got a new one. Sometime in the 90s Ford...
  8. Saleen0679

    Once and For All.....Door to Body Weather Stripping Shootout

    It's original Ford. I bought it many years ago. Still in the Ford box.
  9. Saleen0679

    Once and For All.....Door to Body Weather Stripping Shootout

  10. Saleen0679

    I need a miracle! - Father's Day Gift Won't Start

    You have pin 55 circled in the photo. The guide rail is above pin 60. You would need to count six pins in from the right side to find pin 46.There will be a guide rail above pin 42.
  11. Saleen0679

    Electrical 1988 mustang gt wiring question

    Green/Red is for the charging circuit. Brown/Yellow is for the Cooling Fan on the 2.3L. Light Blue is for the Coolant sensor.
  12. Saleen0679

    Battery fitment issue

    Sounds like you don't have the snap-in adapters attached to the base of the battery. A 34/78 fits fine in the stock battery tray with the adapters.
  13. Saleen0679

    Electrical 1993 Cobra Test Connector

    W/P is white/purple. W/PK is white pink.
  14. Saleen0679

    Electrical 1993 Cobra Test Connector

  15. Saleen0679

    89 mustang wiring concerns

    The double BK/W wires are used to test the windshield washer pump. Usually there is a grey connector shell around them. The round 2-pin plug is likely to be part of the A/C harness. An extension harness connects the plug to the compressor.
  16. Saleen0679

    ANewbie with Fox wiring mess

    There are wires with those colors that go to the cruise control switches.
  17. Saleen0679

    Electrical Fuel pump relay

    93 A/C Heater
  18. Saleen0679

    Looking For Oem Fox 87-93 Muffler Stamping Numbers

    From a 1989 Driver: E9ZB-5232-CA Passenger: E8ZC-5230-AA
  19. Saleen0679

    Hvac Temperature Control Cable.

    I've never had to replace a cable, but from what I understand the preset adjustment gives you a starting point for the self adjustment. Without the preset it is possible to kink the cable because it will be forced to open/close the blend door after the door has already reached its limit.
  20. Saleen0679

    Hvac Temperature Control Cable.

    Here are some Ford instructions: Temperature Control Cable Removal 1.) Remove control assembly from instrument panel. 2.) Disengage temperature control cable from cable actuator on control assembly. 3.) Disconnect temperature cable from plenum temperature blend door crank arm and cable...
Top Bottom
Back
Forums
Menu