Search results

  1. R

    95 mustang gt dies when driving starts back up or some times it wont? help please

    Distributor I agree with BlackVert. I just had to do this on my 95. MAKE sure you get a new one. Not a reman!!! Most of the reman test the pip and it tests good since it is cool. Get it in your car and you have the same problem. Had a guy go through 4 before he bought a new one. Mine cost...
  2. R

    Re-ring the motor?

    Lazy man overhaul Modern rings (moly rings that is) are pretty impressive. So if the cylinder walls look ok or you can see some crosshatching left in the walls. Ream the ridge on the top of the cylinder off and rehone the cylinders. But I would not reuse the bearings. It is too cheap to...
  3. R

    Tucson?

    I am local Tucson guy here!
  4. R

    Need an AIR pipe for emissions

    I love this place. I found a guy in Phoenix that has one off a 93. I am hoping that is close enough to do the job. He said I could silicone hose at Napa. I just bought the new cats today. Plan on getting them welded later this week. Man emissions is a pain.
  5. R

    Need an AIR pipe for emissions

    Anyone have an air pipe or a suggestion or part number so I can get one? It runs from the air pump to the rear cats. Thanks, Dan...
  6. R

    Update on my 95 stang

    Want to say thanks to everyone who offered suggestions and help. These are the mods I knew about. x302 heads e303 cam 93 Cobra intake K&N air filter Trick flow elbow BBK shorty headers Turns out thanks to the 511 code and someones suggestion on here I discovered that it had a custom...
  7. R

    Codes and d**n codes

    Back to the 95 I just got. I have the cats bolted back on, new o2 sensors, fixed the stripped bolt hole on the intake for the upper intake bolt, new gasket for upper intake, plugs, wires, cap, rotor, #19 injectors, and an MSD coil. Mods that I know about: x302 heads e303 cam 93 Cobra...
  8. R

    Little more help please. Injectors.

    Update I found a set of 19# injectors locally and as a + I scored a set of stock valve covers. So maybe I can change the oil without having to pull the throttle body. I also hope that it will let get get rid of the phenolic spacers. I am not clear on if I need the spacer because it is a 93...
  9. R

    Need Help Diagnosing Wailing

    Bearing. I would have to agree that it sounds like a bearing in the tranny.
  10. R

    Little more help please. Injectors.

    MAF pics This is what is on it. The tube it screws to appears to be original and I can find no part numbers on it. Just got a scanner plan to check codes after exhaust install. Thanks again for all the help.
  11. R

    Little more help please. Injectors.

    More details How do I tell what MAF I have? It is easy enough to see. There is no custom tune. So would I be better off going back to the 19# injectors? We run at 32 mph for 2 minutes then they test idle only for 95. I am going to bolt the cats back in and may go to the rubbing alcohol.
  12. R

    Little more help please. Injectors.

    Still struggling to get my new 95 stang through emissions. Here is what I know. I have X302 heads, 1.7 cobra rockers, a E303 cam, with a 93 Cobra upper. To the best of my knowledge it is a stock GT bottom end. It has a O/R pipe, no idea the brand to flow masters The heads had the wrong plugs...
  13. R

    OBD1 plug location

    Thanks Thanks guys, Great forum and I appreciate the help.
  14. R

    OBD1 plug location

    Ok, 95 Stang where the heck is the obd1 plug located. I have tried every search and go 0 on the location. I found a plug on driver side strut tower but it is missing the solo wire. So where is the plug? Thx, Dan...
  15. R

    New 95 stang. Need a little help.

    Air intake What air intake do you recommend? I am not a big fan of this setup just for the reason you stated.
  16. R

    New 95 stang. Need a little help.

    More details. Thanks for the info. Here is what I have. The oil fill plug is located right under the IAC valve. My EGR tube is disconnected from the exhaust but the plug and vacuum are still hooked up. The check engine light is not on. It failed emissions in a spectacular fashion (HC...
  17. R

    New 95 stang. Need a little help.

    I have the following air intake on the new 95 stang I just got. (see pics) It blocks the oil filler plug. Can I convert this to something a little more friendly? The current setup up is x302 heads with a Cobra intake and a phenolic spacer and an e303 cam with 1.7 rockers. Why do I need...
  18. R

    what do i have to do to get the piston rod off the crank?? **pic**

    pistion removal Depending on how many miles are on the engine will tell you wether you have to remove the crank or not. As the engine runs and wears in a ring or lip is formed on the top of each cylinder. You can feel it with your finger. If this is present or deep then pushing the pistion...
  19. R

    Need an electrical connector

    Due to a wiring problem with my power door locks I was forced to tear my dash apart to get to the wiring harness. The gray socket that plugs in the emergency blinkers broke. The little plastic toungues that hold the connectors in the sockets have all broken. This appears to be the same...
  20. R

    MSD 6a no start

    I have a 92 mustang lx 5.0. I wanted to put an MSD on it. I got a used MSD 6a and an MSD harness and put them on. The car won't start. I then sent the MSD 6a back to MSD and they checked it out saying there is nothing wrong with it. I went back to the car and I had put an MSD coil on the...
Top Bottom
Back
Forums
Menu