Search results

  1. Z06killinSBF

    AOD conversion parts ALL NEW

    All these are new, never used. Lokar TV cable and carb bracket for Holley carbs -$100 B&M bracket and lever kit for AOD.-$45 Scat flexplate 28oz 164t-$50 TKO/AOD/T5 conversion crossmember for 65-66 Mustangs-$100
  2. Z06killinSBF

    TV cable bracket modify

    I'm not sure if anyone else has run into this issue. What do I need to do to modify the bracket for my TV cable as it is designed for a Holley and I'm running an Edelbrock? I am using the Lokar cable/bracket. Thanks.
  3. Z06killinSBF

    Street Avenger issues

    New Holley Street Avenger 670 problems consist of: 1) won't smoothly idle below 1k. Wants to maintain idle around 1100 or else it surges then dies. 2) Bogs really hard upon tip in or WOT. I installed the black vacuum sec spring to no avail. 3) decides to have random idle/throttle hangs...
  4. Z06killinSBF

    Rear seat

    Does any one know if the back seat from a late model will fit a 65/66 coupe? I would like to put in a back seat in my car but all the old seats cost an arm and a leg.
  5. Z06killinSBF

    Stereo work

    I recently got back into stereos and decided to try my hand at fiberglass work. I am extremely happy with how everything has turned out. Now to just finish the trunk and do a console.
  6. Z06killinSBF

    Wheel PS thoughts

    I have been tossing the idea around of having black wheels on my car. I think it looks pretty cool. I also blacked out the window trim which I will be doing in the near future. Before: After:
  7. Z06killinSBF

    EFI swap question

    OK, searched and no luck on this one. I heard that in order to use the 289 cam on an EFI swap, you must rewire the fuel injectors to the appropriate cylinder. Is that true?
  8. Z06killinSBF

    Long tubes or Tri-Y's

    I need to change my old, beat up and hammered on headers for my up coming AOD swap. I have always liked the Tri-Y's but they only come in 1-1/2 primary and 2-1/2 collector. I would prefer the ones with 1-5/8 w/ 3" collector but those are $500+. Would I notice a difference between the smaller...
  9. Z06killinSBF

    Factory gauges

    I want to make my factory oil, amp, and temp gauges to work. Can I use generic sending units or do I need specific ones? I found the ones on California Mustang for about $30 but I don't know if some ones off a 5.0 would work. Also, what does it take to make the amp gauge work? Thanks
  10. Z06killinSBF

    Electrical issue times 2

    Ok after 2 extremely simple jobs, I have totally got myself in a problem. #1: Pulled gauges to replace dash pad. Put back in gauges, test, no lights. Find blown fuse, replace fuse, test, fuse blows, no lights work. Hmm. I know my dimmer works as me being a genius wired my tach light to the...
  11. Z06killinSBF

    Exhaust tips?

    Currently have dumps and I am getting tired of the booming. Should I 1) keep the exhaust hidden, 2) Bring tips (3" slant) out under tail panel, or 3) cut out the tail panel and run the tips under that? Examples: Cut out: Hidden:
  12. Z06killinSBF

    Headers

    What are a decent set of headers that will fit good on an AOD swap? The current ones I have are really tight to the C4 trans and have been hammered on over the years. I am looking for a long tube type so no shorties. Thanks.
  13. Z06killinSBF

    66 Mustang back seat

    No longer needed.
  14. Z06killinSBF

    Bolt question

    What is the thread count/information for the bolt that holds the gas pedal to the rod? Mine is stripped and needing an insert. I have the new bolt but have NO idea how to tell what I need. Thanks.
  15. Z06killinSBF

    Fuel level??

    I recently had my gas tank out and everything removed to have my sump installed. After I got everything sealed up, the level doesn't read. My sending unit is only about a year old and the gauge works when grounded. I also have a proper ground on the sending unit when checking it to chassis. Is...
  16. Z06killinSBF

    8.8 axle Q

    Can I run my 8" axles in an 8.8 with 9" housing ends?
  17. Z06killinSBF

    Spring mounts

    Where can I get leaf spring mounts for an 8.8? All the ones I find are 3" and the 8.8 is 3.25" correct?
  18. Z06killinSBF

    Fox exhaust

    Will headers and a mid pipe from a Fox body fit the 65-66's with no/little issues?
  19. Z06killinSBF

    Tuning Q

    I never thought about this but, if your running a 160 T stat vice a 180/195/205 should you also run colder plugs? Also, since I have a 160 stat, what would be a benefit to go to a 180? I'm just trying to make my car more drivable. Lastly, while cruising around @ about 60mph (3k rpm) it...
  20. Z06killinSBF

    351W 400hp??

    I just scored a rebuilt 69' 351W long block. Is it capable of making 400+ hp with stock heads (home ported) and rotating assembly? I'm thinking a Funnel Web, solid lifter cam, ported stock heads, electronic ignition, etc... Ideas?