Search results

  1. Black95GT_Kid

    strange strut noise?

    Friday I installed Eibach lowering springs rear upper and lower control arms and Strange struts and shocks. Now the car make an awful rattle from the struts. After a little research Im discovering that the struts are slightly undersized and cause a rattle when used with caster camber plates. So...
  2. Black95GT_Kid

    cobra r hood?

    Im a little confused about the Cervini's Cobra R hood. I have seen it advertised as a 3.5 in raised center and the factory hood as a 1.5 inch. I did a quick search and was not able to find a clear answer for my question. So my actual question is weather or not the Cervini's hood is taller than...
  3. Black95GT_Kid

    rock auto cobra bumper?

    Has anyone else checked out rock auto for a cobra front bumper cover? Ive found that they have one for $135. Im not a body expert, so does anyone have experience with rock auto body parts?
  4. Black95GT_Kid

    New engine start up

    Im currently building an engine for my car and am going to turbo it. Im curious if the stock tune is safe enough to break the engine in before i have it dyno tuned or if i should get a pre tuned chip the will be close for initial start up?
  5. Black95GT_Kid

    bbk fuel regulator?

    i recently put a bbk fuel pressure regulator on my mustang. it worked fine but i am now having a power problem under load. i tested and replaced numerous items. finally i vacuum tested the regulator and it will not hold pressure has anyone else had this problem with the bbk regulator. thank you...
  6. Black95GT_Kid

    Cobra intake and strut tower brace?

    i bought a cobra intake on ebay and the strut tower brace doesnt fit which i knew it wouldnt. frpp makes the m-20201-A51 but i am noticing that stock cobras do not have a strut tower brace. is this the way they came stock, and can my GT function ok with out it for a while till i can get the...
  7. Black95GT_Kid

    custom chip?

    im a little new at doing major mods to a F.I. engine. ive done plenty of carb. engines so i dont know much about custom chips. so the question is what is a good brand chip? Here is a list of the new mods if that helps...
  8. Black95GT_Kid

    twEECer users!

    i dont know much about the tweecer. i am building up a 306 and will ultimately need some eec changes. how easy is this product to use. i have some basic knowlege of the eec unit from school. i would appreciate any feed back. thank you
  9. Black95GT_Kid

    306cid camshaft?

    im building a 306 with stock heads and intake port matched or possibly a cobra intake and i put a thread on here sayin that i was goin to use a e303 cam and was told to use a different cam so i found a crane cam with a Duration of 276/ 282, and a Lift of .513/ .529 is this better?
  10. Black95GT_Kid

    Engine Build UP!

    I plan on building a 306. i plan to use stock heads with 1.7 ratio rockers, e303 cam, Federal mogul rebuild kid .030 over bore, frpp lifters, new timing gears and chain, pushrods, arp connecring rod bolts, port match stock GT intake or a cobra intake if i can find one for the right price in...
  11. Black95GT_Kid

    EPEC?

    does anyone have the epec system? how much does it cost? how easy is it to use?
  12. Black95GT_Kid

    FRPP ENGINE MANAGEMENT SYSTEM?

    on year one there is a frpp engine control system part number FR233 does anyone have information on this product. year one does not give enough and i cant find it any where else i would really appreciate some help with this.
  13. Black95GT_Kid

    frpp engine control system

    does any one know info on the frpp engine control system sold by year one they seem to be the only ones who carry this product and i cant find any information.
  14. Black95GT_Kid

    HELP IDLE SURGE!!!!!

    when my car is at idle it will surege between 500 and 900 rps and will somtimes almost stall. ive tried cleaning the idle control motor, changed tps, changed pcv valve and im running out of ideas. any ideas would be well apreciated.
  15. Black95GT_Kid

    cobra upper and gt40 lower?

    Will a 94-95 cobra upper intake manifold fit on a gt40 lower manifold?
  16. Black95GT_Kid

    cobra intake

    im looking for a 94-95 cobra polished upper intake. does neone know where i can get one and does it make a difference over the stock gt. please respond.
  17. Black95GT_Kid

    pypes performance x pipe

    i just recently bought the pypes performance catted x pipe that is ceramic coated brand new from the dealer for $250 it was the display model for a little bit but has nothing wrong with the cats or coating. is this a good deal or not? has neone purchased parts from this company before id like to...
  18. Black95GT_Kid

    cobra rocker installation

    i just purchased cobra rockers and need to know if the pedistal seats need to be cut to allow for proper seating I NEED HELP!!!
  19. Black95GT_Kid

    exhause combo need help!

    ok i have a flowmaster american thunder cat-back system and was lookin into a pypes performance cated x-pipe i was woundering how much louder that would make my car and if you have any opnions on their products or any suggestions of a better cated x-pipe. i need the cats since i live in...