Search results

I've had 100 people look at my car on ebay but no bids. Do I have it overpriced...

There is a blackish and a purpleish wire that go to this A/C clutch activation switch. Can someone tell me which side goes to which? Is there a fuse involved anywhere? Thanks.

Okay, so I had a little valve train noise so I pulled the upper intake and valve covers to investigate. Only problem is that I neglected to remove a couple washers off the upper intake and they "disappeared"! I Found one but not the other..thought I heard it clink down the long tubes but I’m...

When I jack up the front of my car, with one side wheel on a ramp and the other free (jackstand on the other chasis side) I can physically hold the wheel and rock it back and forth (sma plane it steer through) and it will rock about 1/8th". The wheel is tight on the spindle and I can see the...

:nice: Just bought some 03 Cobra seats and the harness is 4 pin. Need to figure out how to wire them to my 94 two pin.// any thoughts/diagrams?

Just bought the seats. Stock is 2 pin harness, Cobra's are 4 pin...preesh any help...

I'm thinking of doing this bumper wit the stock skirts and side scoops on my black coupe and was wondering what it might look like. This is a vert but if I could see it black that would help my decision..thanks!:nice:

When I steer back and forth, my car goes "krunk, krunk, krunk, krunk, krunk". There are definitly no obstructions hitting the rod ends or LT headers/steering shaft but at low speeds there is stick-tion in the steering. If I steer back and forth at idle and the steering pump buzzes a bit and...

These are the Elite Lumbar 1200 by scat/procar. Does anyone have any expirience with these as far as appearance and comfort goes? Thanks. :nice:

The last couple times I have been on a high speed "flyway" interstate ramp I'll be driving around the curve and all of a sudden my car starts to drift out of the turn as if I cut the wheel that way...I take my foot off the accelerator and give it minor break and it goes away. I should add that...

My clutch had been feeling notchy and was stretching out, it snapped today. I checked underneath and verified the broken cable. What I could not recall though was whether it was right that the clutch fork swung easily toward the rear of the car. I had not remembered there being any play last...

I've been advancing my timing and listening for a ping. i just went out and when I got on the gas there was kind of a high pitched whistle. I backed off the gas and it went away. Is that what a ping sounds like or is it more likely an intake leak or something?

I am installing some air springs and part of the install requires that I run a wires from the ECU to the ignition (12v only when key is on), and illumination (12v only when lights are on - for dimming guages). There's also a constant 12v and ground but I can figure that out. I don't want to do...

I have a 94 GT but not many of those guys seem to have the d-spec and it seems more prevalent here. I'm going to an Air Ride suspension and I'm trying to decide if I should replace my failed Tokico Illumina strut or go ahead and get D-spec at all fours. I'm trying to grasp how much I'd...

I'm not real big on the mag but I had to check it out when I saw the Mach3 on the cover...dude MADE ONE! The trick is that he improved on Ford design a bit and he built it on a SN95 IRS chasis..it is so beutiful it makes me feel proud by association. I'll probably go tomorrow and buy it so I...

I've had this set up for months but it’s been noisy lately and it got me thinking about how unstable it seems. I think ideally, the cap on top of the spring would interface with the bottom of the cars chassis. The problem with that would be that it would set in the 3-4" hole in the strut tower...

I have a problem with my brakes where as I am stopping (easy braking) and easing pressure off the pedal, I feel a little brake slip. A mechanic I know suggested that it might be a problem with the ABS system and that the hydraulic control unit might be pulling fluid pressure from one or more or...

I just had a new clutch installed. My King Cobra was shot. I went with a HD FMS-M-7560-A302N (veleo?) and FMS cast iron flywheel. I got it back after install and it feels nice until I hit about 5000 rpm. Then its not horrible vibration but its definitly a lot more vibration than there was...

I currently have a 70mm that I was using before the 347 build. Unfortunatly, I had drilled a hole in the TB plate as a "trick" someone suggested for improving idle. I think its causing some problems. Anyway I was thinking of going smaller with the FRPP 65mm but wondered if this was too small...

I was considering it and wanted to see it first., thanks