Search results

looking for a litte feedback here hopefully can get this figured out. just dropped in a fresh 306 and everything is good but not 100% perfect. i thought it may have been tune related but i started over with a fresh tune also and everything is dialed in according to the wideband and kams. i had...

need a little help here. it happens when backing out of a spot or driving at slow speeds. mostly around turns and in parking lots. it only happens when engaging the clutch. if i disengage the clutch while its happening it stops. seems like if you try and drive it normally is when it happens. i...

having a bit of trouble getting this thing back in. im thinking about pulling the differential out and removing the ring gear for more clearance. i would mark the ring gear so it can go back in the same spot. if i do that can i just put the differential back in and finish up with the install or...

what kind of driving conditions should i log for slopes and breakpoint? should i just do an idle to 2k like the maf and isc settings or do some driving around?

if you disconnect the alternator plug should the battery light come on? im trying to figure out why my alternator is not charging. only seeing 12.1 volts. battery light is not on. alternator and battery test good. all power and ground wires were upgraded to 2 AWG cable. i also installed a new...

can some do me a favor and check on their alternator and tell me what color wire goes to the top of the plug if looking from above? green/red or yellow/white?

im starting to work on my maf transfer and tb airflow & isc in EA but want to make sure im starting out with the right settings. my desired idle is 850. if i have idle in drive and idle in neutral set to 850 what would i put in for the isc max rpm in drive and isc rpm at CT? are those the only...

im trying to determine the proper pushrod lenght and need some help. from what i have read the sweeps should be narrow and centered. i started with the stock pushrod and the sweep is dead center but its wider than most of the pictures i have seen. its about a 1/4" wide. is that too much? next i...

i noticed this started happening about a week ago. i thought maybe it was bad gas but i filled up again and its still there. i pulled the codes today and came up with 565, 314, and 311. i did a search and others suggested that 314 and 311 will come up if you deleted smog. the cannister purge is...

i have a chirping noise and i wanted to get a few opinions before pulling the tranny just to change the TOB. i had the same chirping sound when i first got the car but it would do it at idle and anytime the clutch was engaged, and go away as soon as you disengage or apply pressure the clutch...

i noticed that whenever the car is hot enough for the fan to come on, it will surge when i start it. other than that the idle is perfect. doesnt surge or hunt at all. i think it is related to the fan and charging system. as soon as i hear the fan the volt gauge drops down and goes back up a...

i would search but im walking out the door and dont have time. what number fuse on the box cover is for the cig lighter and accesory outlet? thanks, greg

im going to redo the nos wiring when i get a chance. other then that i hope to go to moroso wednesday and friday weather permitting :)

i have a nos dry kit with the jets for 80 and 150 shot. the 80 are in there now. what would it take to run the 150 jets? i have stock injectors, a walbro 255 pump, and adjustable fpr. i heard about putting a shim in the nitrous regulator and it ups the fuel pressure but should i wait until i get...

i just picked up a nos dry kit. im probobly going to install it this weekend. do i need a bottle blanket or warmer? also, if you have pics of where you mounted the solenoids please post them. thanks

its very minimal but enough to notice while driving. its been like that since i have had the car. i can see the steering shaft has the same amount of play in it as i wiggle the wheel side to side. is there someting else i should check first or is the only way to fix it to get a new shaft. thanks.

question. IIRC, changing to a 7 tooth gear drive, red 21 tooth gear, and 3.73's out back will make the speedo 100% accurate. is this correct?

mines shot. the black plastic coating is cracking. anyone have one thats in decent shape laying around?

is that the correct term? are there any other names for it? anyone have a part #? i went to the parts store and ended up walking out of there with a mainshaft seal. looks similar. i found it on 50resto but i really dont feel like paying $20 if i can get it locally. does this look right?

is that the correct term? are there any other names for it. i went to the parts store and ended up walking out of there with a mainshaft seal. looks similar. i found it on 50resto but i really dont feel like paying $20 if i can get it locally. does this look right?