Search results

  1. AUcobra94

    FS: AFR 185 Heads

    Interested in heads sent you an email. Thanks, Dan
  2. AUcobra94

    Camshaft Dowel?

    The crane 2031 came with a short and a long dowel, I don't remember why but I used the short dowel.
  3. AUcobra94

    Meats and skinnies?

    thanks mustanggt95, I thought the 275 would probably be fine on the 10" rim. If anyone knows the backspacing I need, please post.
  4. AUcobra94

    Meats and skinnies?

    ttt
  5. AUcobra94

    Meats and skinnies?

    Guys I think im going to order some of those cheap summit or jegs knock off welds(pro stars). I want to go with 10 inch width on the back, the only backspacing they come in is 4.5"; is that the correct backspacing I need; is the backspacing measured from the inside of the rim or the outside...
  6. AUcobra94

    oil pressure gauge?

    I was going to put one in the car, ive just been stalling. I guess Ill put a water temp gauge in at the same time. thanks
  7. AUcobra94

    oil pressure gauge?

    My oil pressure gauge is dropping to 0 at low idle, around 800rpm. If it is idling higher than that or if i'm driving it will go back to normal. Do ya'll think it is the oil pressure sensor or the oil pressure is actually dropping at idle? Has anyone had this happen to them? I'm hoping the...
  8. AUcobra94

    oil pressure gauge?

    My oil pressure gauge is dropping to 0 at low idle, around 800rpm. If it is idling higher than that or if im driving it will go back to normal. Do ya'll think it is the oil pressure sensor or the oil pressure is actually dropping at idle? Has anyone had this happen to them? I'm hoping the...
  9. AUcobra94

    What should my 94 Cobra Run 1/4 mile

    high 13s
  10. AUcobra94

    stonger rear?

    I just ordered(from summit) the Alloy usa axles. They are in the mustang section for $209, and they have a 10 year warranty.
  11. AUcobra94

    1st Dyno run on my KB Cobra

    I would look for a mechanical problem before I went out and bought heads or exhaust. First it should pull past 5200rpm. I think you should be making more power, my friends 94 lightning with the gt40 heads and intake went from 270 hp to 390 after his blower(centrifical @ 8psi). Do you have...
  12. AUcobra94

    New Heads/Cam or Nitrous???

    The intake is probably holding you back a little. Dont get new head just port the ones you have. As far as the intake goes you can port it or get a performer rpm or a trickflow trackheat. I just put a trackheat on my car and it didnt hurt my bottom end at all and it pulls to 6000 rpms now...
  13. AUcobra94

    nitrous

    It would be nice but you dont have to have a bottle heater. I put my bottle in hot water for about 15 minutes then rap it in a towel, it will stay hot for about 2 or 3 hours. I mounted my solinoids at the very top of the fire wall. If I find time I will make you picture and send it to you...
  14. AUcobra94

    nitrous

    It would be nice but you dont need a bottle blanket or warmer. I just put the bottle in hot water for about 15 minutes then rap it in a towel, it will usually stay warm for a couple of hours. I mounted the solenoids on the fire wall, if I find time ill make a picture and send it to you.
  15. AUcobra94

    swap to a 351

    Hey guys just want to know what is involved with this swap. I know intake, but can what about motor mounts, bell housing, accessories, and processor/sensors. Maybe someone has a good thread or web site on this. Thanks for any responses, Dan
  16. AUcobra94

    does anyone watch the shield?

    I watch religiously and this season was f-in crazy. I cant wait till next season, Shane is dead.
  17. AUcobra94

    spec clutch no pressure plate?

    ttt
  18. AUcobra94

    spec clutch no pressure plate?

    I got a new spec stage 3 clutch disk but no pressure plate. I called spec and they want $200 for the pressure plate. Does anyone know where I can find one cheaper? Is it a bad idea to use a used plate? Can I use a different(company) plate than a spec? Thanks Dan
  19. AUcobra94

    Will this "safely" get me in the 12's

    Exhaust will make a big difference with your setup. Mine went 12.80 on and 80 shot(I didnt spray in 1st gear because of street tires), and my setup is close to the same except for exhaust and maf. Besides nitrous the exhaust made the biggest difference in hp in my car.
  20. AUcobra94

    I need a new clutch kit

    So the HD clutch kit is better than the KC?
Top Bottom
Back
Forums
Menu