Search results

  1. P

    HESITATION - 96 cobra

    maybe you can install a new fuel filter? I had the same problem with my engine and I installed a new fuel filter and it's all gone ! :)
  2. P

    nitrous help

    on my zex setup i had the power for the controller(window switch) on a different 12v switch So when i start the car, the WS open and if i activate the arming switch for the solenoid then it can activate the solenoid if in the RPM range and at WOT
  3. P

    What Tuning Software should I buy?

    SCT Pro-Racer Package with training DVD an book http://www.vmptuning.com/store/index.php?p=catalog&parent=70&pg=1
  4. P

    fuel pump mustang gt 98

    Hi I've a 98GT but the build date is 10/97. I've swapped the 4.6 2v for a more powerful 5.4 4v and I want to upgrade my stock fuel pump. I had a deal on a walbro 255lph gss342 with the basket and all the wirings. I've also a t-rex 50gal/70psi in the garage. I want to know If the gss342...
  5. P

    96 Cobra bogs during hard acceleration! Help!!

    +1 for the plugs and wires ... or fuel filter
  6. P

    strange vaccum issue....

    if you problem is not already solved, you can try to clean your IAC before remove it, take extreme care to not break the paper gasket, fill the 2 holes with brake cleaner or carb cleaner or something similar, do it maybe 5-6 times, you should see all the dirt and crap is removed after, wait...
  7. P

    car wont start ...

    Thanks Tommy ! finally it was my plugs ... I've replaced all 8 and the car started ! :D :D I'll change my oil because it's flooded with fuel. but at least it's working now ! i'm so happy thanks again for the tips ! Rich
  8. P

    car wont start ...

    Hi, I've a really strange problem with my mustang. I were able to drive for 17km without any problem then suddently the car wont start. It's cranking, cranking and cranking but it wont start. At first I tought it was the crank position sensor so i replaced it... no luck I verified, I've fuel...
  9. P

    4.6 to 5.4 Swap Whats needed

    COP is Coil On Plug, ford changed to COP on mustang 99 + for the picture, i'll send them this weekend ! do you plan to port your b head ? what kind of power do you expect ? for the intake, I've a 97 cobra intake cutted in half, widen and rewelded.
  10. P

    4.6 to 5.4 Swap Whats needed

    What's your email? PM your email i'll send them over email
  11. P

    4.6 to 5.4 Swap Whats needed

    http://www.cmoc.ca/forums/members/phoenix330/albums/26/99.jpg http://www.cmoc.ca/forums/members/phoenix330/albums/26/100.jpg http://www.cmoc.ca/forums/members/phoenix330/albums/26/101.jpg http://www.cmoc.ca/forums/members/phoenix330/albums/26/102.jpg...
  12. P

    4.6 to 5.4 Swap Whats needed

    Hi, i've done it... block is from a f-150, heads/intake/pcm from cobra 97 The engine is taller, so you will need a new hood. You will need 4v headers if you're using 96-98 cobra intake/heads, i can send you some pictures of my intake. you can reuse your stock pcm BUT you must have it...
  13. P

    car not starting ...

    well it was my crank position sensor who was dead I replaced it and it started like a brand new car !
  14. P

    Hard starts slight miss at idle

    check for the compression in each cylinder maybe a vaccum leak ?
  15. P

    car not starting ...

    Thanks, I'll look for the crankshaft sensor. for the wiring, it's from a 97 cobra. the engine was running fine before this.. do you think a sensor can stop working just like that ? Thanks again !
  16. P

    car not starting ...

    but if I reinstall my cobra PCM with the chip, normally the PATS will let the car start ?
  17. P

    car not starting ...

    Hi, i've a really strange problem with my mustang. I've swapped my 4.6 2v for a 5.4 4v. I've swapped the PCM of my old GT(98) for a Cobra(97) with an sCT chip with PATS off. I've drove the car for about 11 miles and then the car won'T start anymore ! I've fuel to the fuel rails, I've...
  18. P

    zex wot switch or window switch? how can i control WOT?

    I've the Zex Traction control unit and it's very easy to install/configure. The only thing you MUST do before installing this unit is to do the programmation of the NMU BEFORE plugging the TC unit, otherwise it WON'T work !
  19. P

    98 4.6l intake manifold

    Hi, I've a friend who worked for a Ford dealer a couple years ago and he told me the police pack is different from "production" car... I'm living in Quebec, and i've a NPI intake for sale. email me if you want it thanks :canada:
  20. P

    pyrometer gauge

    Thank you very much. I had this when I purchased a wrecked mustang .
Top Bottom
Back
Forums
Menu