Search results

  1. C

    Bone Stock 5.0 Fuel Pressure

    THanks I thought that is what is shoudl be. I am getting a reading of 27, so I don't know if it is the pump or possibly the regulator is going bad.
  2. C

    Bone Stock 5.0 Fuel Pressure

    I am working on a stock 5.0 that has some driveabiltiy issues. What should the fuel pressure be at idle with the vacuum hooked up at teh regulator? With vacuum disconnected and plugged? I could not find and answer to this when I did a search. Everyone seems to have different injectors...
  3. C

    Screeching noise from my engine - HELP!

    I have heard the same thing with my 347. Obviously it is not the belt since you have removed it on your car. I have read that aftermarket distributors have to be ground down slightly on the botom to accomodate hardened oil pump drives. The oil pump drive is not cut down enough to accomodate...
  4. C

    V8 T5 to 4 cyl T5

    I just helped my buddy, sweet88, put a 4 cyl tranny in a v8 car tonight. The bearing fits and everything went right in.
  5. C

    help identifying mysterious black box

    The picture does not look quite right, but the wiring is dead on. Thanks for helping solve the mystery. I cut it out of the car tonight. The wires were burned near the connector and appeared to have been shorting out. I cut all of the wires back and sealed them off with shrink tape...
  6. C

    help identifying mysterious black box

    The #'s are illegible. I found a wiring diagram in my Haynes manual and it shows an ac fan controller that might be the part. One of the main wires going to this thing is a yellow/grey wire. According to the maunal a yellow grey wire goes to the AC fan controller. Do you thin k this could be it?
  7. C

    V8 T5 to 4 cyl T5

    Here is the Federal Mogul pn: BCA 202-SS The search part of this forum is very effective. I found this part # in about 1 minute.
  8. C

    help identifying mysterious black box

    Since it had some relays and heavy gauge wire going to it, I bet you are right. Thanks for solving the mystery.
  9. C

    V8 T5 to 4 cyl T5

    sorry, I meant $15. Don't waste your time on the lathe. Just order the right part. You can order parts in Canada from Autozone by calling 800-288-6966.
  10. C

    help identifying mysterious black box

    The wiper delay still works with it disconnected and there is no indication the car ever had cruise control. Can you think of anything else?
  11. C

    help identifying mysterious black box

    I have attached the picure. Sorry it is not more clear, but my camera phone is not very good.
  12. C

    V8 T5 to 4 cyl T5

    Go get this part. It is the correct pilot bearing to put a 4cly t5 behing a v8. This part # is an Autozone part # and was originally used on a mazda/ ford ranger truck from the late 70's. It costs about 154 bucks. part# 14672
  13. C

    help identifying mysterious black box

    All- I have an unidentifed block box located above/near the drivers kick panel. It has a large grey connector going to it. My car is an 88 4cyl converted to carburetor v8. The car seems to run without this, but I am trying to find out what it is and what it did. The wiring appears to be...
  14. C

    k-member help

    Look at the Racecraft K -member (www.racecraft.com). It does not seem to move the wheels and you can get it with spring perches if you do not want the expese of coil overs. It also allows you to use stock a-arms. It i appears to be well made. My neighbor just installed one on an 88 GT. I...
  15. C

    From EFI to carb'd on an 89

    I just replied to another post about the same thing here are the parts I thought of plus a couple I forgot the 1st time (all of this stuff is middle of the road stuff, you can spend a lot more money if you try): carb manifold -160 carb- 380 distributor- 200 MSD 6al- 220 carb fuel pump- 120...
  16. C

    thinking of going carb

    I have 2 carbed 5.0's both run pretty well, but do not have perfect driveablity. I am using a wideband O2 sensor to help tune, but they are not quite right yet. Mileage is not very good.(about 15.5/gal) If you have a stock EFI system it may be cheaper to troubleshoot and fix than it will be...
  17. C

    tubular K-Member 9 inch rims

    ttt
  18. C

    SOUTHSIDE LIFT BARS, CAN I GET AN OPINION?

    Mine came on the car and are also welded. They hook great. Don't consider removing them. you will be dissapointed.
  19. C

    tubular K-Member 9 inch rims

    Does anyone know of a tubular k-member that does not move the wheels forward. I want to run a 9 inch wide front rim.
  20. C

    any one using procomp alum heads?

    I got the heads on my 347. Here is what I have found. 1. If you are going to buy the heads, get them assembled from a reputable supplier. The pushrod holes going through the head are too small and need to be machined, a reputable suplier will take care of this. 2. Make sure you get guide...
Top Bottom
Back
Forums
Menu