Search results

I used to have an 06 Mustang GT, posted here a lot. Just wanted to stop by and say hello. I still love the 3 valve S197s....... I traded the car in to Ronnie Thompson Ford last September on an 03 10th Anniversary Cobra with 17,000 miles on it (exhaust only). Since then I have added a 2.8...

I have seen the replica wheels on american muscle, but really like these much better. Anyone have any pics of these wheels the S197? Would they even clear the brake calipers? Ford Racing Performance Parts [M-1007-F500*]

Does anyone know if the Shelby GT grille will fit a GT?

I noticed that the Pypes mid-muffler setup is just a straight through mufflers with the over axle pipes and then the delete pipes. I also noticed on the Pypes website that you can purchase just the M-80 mufflers. I was thinking of adding those after my h-pipe and then clamping on some 2.5 turn...

I have a high speed vibration that starts around 90 mph and gets worse the faster I go. So I haven't been driving that fast anymore because I don't want to damage anything. I have had two JPC driveshafts, three spyder shafts and I currently have a shaftmasters on there now. The vibration...

I will be installing Steeda fixed lower control arms and an adjustable Upper control arm. What is the proper way to measure pinion angle on these cars with a one piece driveshaft?

I am getting ready to install a Detriot Truetrac differential with FRPP 4.10 gears. The factory fluid is a Synthetic 75w-140 with 4oz friction modifier. Some have said that I would need to run a thinner gear oil. I have tried to contact Eaton about the gear oil recommendation, they still haven't...

I am getting ready to pull the trigger on an aluminum flywheel and upgraded clutch/pressure plate kit. Looking at what I have seen everyone either has the Centerforce or the Spec kits. I have heard great thinks about Fidanza, but I would like to buy it as a package deal. I am looking to spend...

Anyone here have this system? If so how do you like it? Is there any resonance? Any before/after dyno tests? I also saw these pipes on Brenspeed's website. Here is the link: http://www.brenspeed.com/mustang_2005/images/sfm62ss.jpg I was thinking of either purhcasing the mid-pipe...

I have the FORD service manual CD's, but I couldn't find any specs on factory ride hieght or variance. I measured from the bottom lip of the wheel to the arch on the wheel housing. In the front there is an 8mm difference from the left side to the right side. In the rear the difference is...

I currently have FRPP 4.10s, but I was thinking of 4.30s. I looked at the RPM vs. Gears chart and there really isn't much of an RPM increase in overdrive. I wasn't sure if I should stay with the 4.10 or go with the 4.30s. Would the 4.30 be a better gear for quater mile times/speeds?

I currently have Brenspeed and Bamachips tunes. I like them both, just wondering if anyone here has a VMP or a Tillman speed tune.

I have been running a tune from a well known tuner. We have been trying to work out this problem. After a few months I noticed that my A/F ratio was starting to richen up at WOT and half throttle(11.8 to 12.0). No other changes have been made. I had to take some fuel out to get back to 12.6 to...

Just wanted to let everyone here at Stangnet what happened with my Flowmasters. Around 9 months ago my first set of flowmasters started to rattle and buzz around 900-1500 rpm. I called summit and they sent me a new set at no cost.(Had to send the others back). 6 months after that they started...

I remember reading online about the "Hurricane" engines the Ford is developing. I believe that they were going to have several different sizes of the new engine package 5.0, 5.8, and 6.2. Not sure whether or not they were all SOHC, but Ford does need to have a better engine program. Not to...

Anyone have any news? I read the article on CNL's website but they haven't updated it either. From what I understand FAST had to redesign theirs to try and get the claimed power. Is there any preliminary word on the power the CNL will give on averge?

I just ordered a set of Nitto 555, tire size is 255/50R17. I will be post pics after mounting and balancing them. I have the standard wheels.

I have found two wheels that I like. I haven't found any pics of these wheels on my car. Any input would be nice. Both are 17X9...

Anyone know of any company that has an x-pipe that will fit on JBA Lt Headers? Would it even be worth the $$$ to switch from an h-pipe to an x-pipe? I realized the sound differences and prefer the H-pipe but what about the performance between the two? Thanks

I have noticed since the install of the JPC Driveshaft I have a noise in first and reverse when lifting off the gas. The noise is only in those gears, and if you disengage the clutch the noise will stop. I wonder if the driveshaft is transfering more noise than the stock unit. Anyone else...