Search results

Bought these used from SonicBlue03L in a package deal with some stage 2 cams. Going a different route and bought a set of heads with valves and springs, so i wont be needing them. Was told they have 1500-2000 miles on them and I see no reason to believe otherwise. Part number 84706 From DRI's...

I've got a bunch of stuff that has come off my truck at some point. All prices are plus shipping unless noted, and paypal include 3% If its not in the picture, its not included. I've tried my best to describe each item, if you have questions feel free to ask. Diablo Predator, unlocked -...

I've searched, read and im still stuck. Car is a 1994 cobra, only mods are CAI full exhaust CF clutch installed by PO, FRPP quadrant and FWA. The drove fine when bought but after a while it started having issues going into gear if you let off the clutch at a light when in neutral. I checked...

I know its been asked about 1000 times, but I am deployed and my rock star internet takes about 10 minutes to load a page, so its frustrating to say the least. I havent been able to find a thread with all my all of my answer yet, but have only loaded about 5 or 6 posts so far, so i figured i...

I posted earlier that i had a leak on a port on my master cylinder. I was then told that i have a fox mc on the not an sn95 as i was told when i bought it. It however has some sort of 3-2 conversion. The car has ranger drums and sn95 front calipers/rotors/spindles. I took a pic of my mc...

Bottom of my master cylinder. Square brass plugs, its dripping fluid and causing me to have a hyraulic leak... do you guys think its something i can pull and put a new plug in, or is it going to require a new master cylinder. I already tried tightening it. here is a picture. This is on...

been in cali about 4 months, and about 1500 miles on the car, mostly city. In that time the car has run the brake fluid resevior down to the point the light comes on twice. driving in traffic today the light was coming on while driving, but when i would hit the brakes it would go off. popped...

I am getting warm after extended periods on the highway. did search read about plastic under carriage bit often being missing. I am guess you guys are referring to this red circled lip. if not, than can someone explain what you guys are talking about?

Car is throwing codes 41 and 91. I know from this post http://forums.stangnet.com/788958-code-41-running-rich-brake-booster.html that i should start with 02 voltage, and then wiring harness and then vacuum leaks. here is my issue. In that thread it says to pull the plastic cover off of...

I have a 5.0 out of an 89 mustang(fairly low miles) that we are dropping in a 68. My issue is this, we plan to run carb, and a standard rotation water pump(no serp setup) I have found a 5.0 timing cover with the part #E3AE-6059-CA is the waterpump for this going to be standard rotation?

Ok, the car is an 89 vert. 5 liter with a 5 speed. Motor is fresh with approx 2500 miles. GT40 heads, e cam, 24lb injectors, explorer intake, bbk 65mm tb, c&l maf for the 24's, short tubes, no cats, no ac, no smog pump, no egr, no can purge. All the emission stuff was off when i bought the...

My friend and his father bought out the dragstrip in Walla Walla, and they are putting on some races this year.... FWIW, his fast time is mid 7's in the 1/8th

I have 89 vert. its lowered on BBK springs, has stock shocks and bbk upper and lower rear arms. it rides like a canned pile of ****. I have been reading and thinking about getting some bullit springs and tokico blues. one question is, is everyone buying used bullit springs, or is there a...

First off, my car and mods 89 vert, 5 speed, a9l computer new motor with GT40 heads, e cam, explorer intake, 24lb injectors, c&l maf, bbk cai. EGR is gone, smog pump is gone, off road h-pipe. if you need any other mods, let me know. Ok, so i ran the KOEO test, and came up with 84 and 85...

Ran into an issue when tearing down my rear end. Not happy with how tight my yoke is and plan to replace it. I however dont have my car near me, and need to order one. I know the OD of the yoke is 4.3" but can anyone tell me the spline count? Thanks a ton.

Im trying to find one in a wrecking yard that doesnt have any foxes. so i need to know what models and years i can cross reference this.

I got a short block with my mustang, that i know is no good. however, i got curious while looking at it, the block is casting E7TE-CA but the rods are D10E-AA is this pretty standard, or has someone rebuilt this before? Also, someone wants the rods(for free) only if they are HO rods...

Has anyone done this(those of you that are the original owners don't count). I found an insurance card in my center console today(did a heater core) and its from the year my car was made. found the location of the insurance office, and googled the owners names using that town. they both...

Who's had a shop do theirs? What did it run?

Ok, so i just dropped a new motor in my car, stock rebuild on the bottom end with a .030 overbore, gt-40 heads and explorer intake with E-cam. I didnt research the fact my stock springs were no match for this cam. So, here i am with an assembled engine, in car, needing to swap out my valve...