Search results

  1. T

    CPRstreetmachines 1969 Turbo'd Pro-Touring GT2 build

    hey! what rear breakes are those?
  2. T

    hyd throwout toploader/jericho

    well i ordered the mcleod hyd throwout but they dont make them adjustable anymore. they must have your measurements. well what if i later upgrade to jericho? well i havent asked them yet but i am thinking if i cant adjust it. then it is only good for that clutch/tranny. maybe i am wrong...
  3. T

    gt40 heads..need better ratio rockers

    ok thanks maybe the guy i got my gt40's from swapped out the rockers then becasue i already have them installed and the rockers are stock pedestal...look nothing like the crane ones. and i think they are from 92 or 3... he said they were cobra's as well. and they are..i know how to i.d...
  4. T

    gt40 heads..need better ratio rockers

    what are some good better ratio rockers for gt40 heads that will clear cobra valve covers? whats a good ratio? i think i recall hearing 1.6? who makes a good set(brand)? and who has the best prices?
  5. T

    Torsional rigidity test: 67 coupe

    reenmachine why did you put the bars on the wheel side rather than the engine side? did you do it to keep the engine bay stock and clean looking?
  6. T

    g force lap time contest

    have any of you measured your g capabilities? i saw a guy at willow that had a gps device that measures lap times and g forces via sattelite. he said its accurate as it checks in with the sat. 16 times a second or something like that. if you have some specs lets hear em tire size and side g...
  7. T

    Flaring a 65 Fastback?

    ? what would a narrower track width do to the g handling? can you pull a g or near? good stuff thanks.
  8. T

    Wheel Hop..grr.

    . thanks on the ranchos stocker! where you get the clamps from on ebay? 10sec the pic ga289stocker posted below shows the under rider bar installed.
  9. T

    Wheel Hop..grr.

    ? what are the rancho shocks part number? good read. thanks
  10. T

    pain in the rear!

    thanks mine will stay stock length. thats what i was thinking to do it just on the leaf side and pretty darn close too, but if it clears i think it will help. i have a mig welder, so i think i can just sopt it enough to hold(like 3 secs.) i think its either that or hacksaw or cut(if i can...
  11. T

    pain in the rear!

    i broke my shackle.. already broken but still holding. so i made some. problem is the old shackle keeps turning when i try to take off the nut(because its broken) so hopefully i can tack weld it without burning the bushing. i guess i can cut the nut off. or maybe you all have a...
  12. T

    turning radius

    ^ anyone else care to chime in about the centering of the centerlink when the pitman has not bee removed?
  13. T

    turning radius

    ??? hmmm, i was told to center the tie rod holes on the centerlink to the frame, and i have power... am i doing it wrong? how to know where the pitman should be pointing as well? i know how to fix bumpsteer, and was told to center the centerlink... any help on this? thanks
  14. T

    Overheating but only when keeping engine above 2k rpm

    ? what causes the hose to close? i (thank God) have never had that problem, and i dont have coils in my hoses. should i put some hanger wire in the hose? suggestions? thanks
  15. T

    When do you NEED posi?

    so... i was at the local track left and right turns and i se an expensive 65 fastback going around a corner then he gunned it and came very close to the wall. is mechanical rear better than clutches? they use clutches in nascar dont they? i am looking to buy a complete from currie or detroit...
  16. T

    need pics of cars with cages. Backseat area?

    henry_v henry_v on page 9 what are those at the bottom? oil slinger? nice car.
  17. T

    Hardtop 'Vert?

    hey! i would do a search for the guy (kid) that made his coupe into a convertable/hardtop(it was yellow). it was very cool. so if you get a roof and maybe some other body parts you could morph your car into that. i have also seen the coupe turned into a fastback. and different year 1/4 panels...
  18. T

    Any good shops in the Los Angles Area?

    NO! stay away from fly ford, i know fisrt hand. try simpson frame and alignment on gower in hollywood. he is the absolute best.
  19. T

    Rear Adjustable Sway Bar

    cool thanks anything like that for the front? does it weld on to the axle? i am thinking of putting one on my 66 fairlane. thanks
  20. T

    Rear Adjustable Sway Bar

    . yes where can we get that bar in the pic?