Search results

Does anyone know how to tell the difference between a series 2 and 3 PMS? It's the old handset but I believe it was upgraded. No sticker on the case and cant power it up. I do have the manual however. Any help would be greatly appreciated

I have the chance to pick up a 94-95 tube K member. Will it fit a fox car some companies seem to have the same part # for both years anyone with experience?

Ok so I am thinking about selling my vert I realy don't want to but I rarely drive it and there are other things I could use the cash for. I have no idea what it might bring however. here is whats done at least the short list 1986 LX vert originally paint is 2 years old and was done at a...

I am still trying to run down all the codes after the motor swap. The two I am having trouble with are codes 66 and 98. I know 66 is the MAF but I went trough the surging idle checklist and I think I just had a loose pin on the computer (#9) tied to wire C on the Maf harness I believe. Anyhow...

I need a little help guys. I just got the new motor in and am having some issues with the idle among otheer things. I just pulled the codes and here is what I got: 23 TPS out of range -I know what to due there 95 Secondary fuel pump circuit failure- I think this was from the MAF conversion...

I pulled most of my A/C off when the motor came out and am wondering if I can pull the vac line that goes into the firewall. I believe it controls the dampers on the A/C but am concerned if it also controls the heat. Anybody have any info on this? Its the small hard line that goes in near the...

Hey guys, I need some help selecting a cam for my motor, I have a couple in mind but I could use some guidance. Here's what I have so far 71 351w .30 over forged pistons -13 dish gt40 y303's (box stock) 1.6 rockers comp mechanical roller lifters efi c-4 with 2400 stall 3.27...

Does anyone know where I can get a set of 351w swap longtube headers that will work with a c-4. Almost everything says manual only. going into an 86 I would like to keep the longtubes so I don't need to swap mid pipes

I am about to start the bay on my 86. I recently bought a hydroboost unit and would like to use it in my car. I know that guys have done it when swaping to a mod motor. Has anyone done it with a pushrod engine. I am trying to figure out if the power steering pump is big enough. I dont...

I just about to start putting the 351w into my car and was wondering if I should bother getting the retrofit hydro linkbar lifters or just put the mechanicals in. I would like the hydro lifters but the price is about enough to scare me off. What are the differences between running the two...

http://cgi.ebay.com/5-0-Mustang-Twin-Turbo-Kit-Incon-1000tti-Complete-kit_W0QQitemZ110065138942QQihZ001QQcategoryZ377QQssPageNameZWDVWQQrdZ1QQcmdZViewItem SCAM ALERT I purchased this kit 3 weeks ago and it is resting peacfully in my garage. There were only 10 made ever I doubt this guy has...

:damnit: This is what my car looked like when I got it about 9 Mo ago... Here are acouple I just took (sorry its getting dark out) So here is the deal I got the car like 9 mo ago. Did a few alot of upgrades plus the bunch the guy who had it before me did. I got it with...

I just got an ATI procharger d3m blower. I did not know anything much about it when I bought it (obviously) I called tech support to run the serial # and found out this thing is friggin HUGE. I have a basically stock motor right now, nothing too special just intake, TB, headers, no cam, stock...

I have a line on a set of rims that I have wanted for some time and no access to my car right now so If anyone could help I would appreciate it. I need to know If a set of 17x8 rims with 4.25 inches of backspacing will fit under my 86 cert. The car also has 2 inch lowering springs thanks

I want to do a 5 lug swap AND pickup another 3/4 of an inch in width up front. I read somewhere that the 96+ spindles will push the width out about that far. Has anyone done this to their fox body if so what all is involved? Any help greatly appreciated

I want to do a 5 lug swap AND pickup another 3/4 of an inch in width up front. I read somewhere that the 96+ spindles will push the width out about that far. Has anyone done this to their fox body if so what all is involved? Any help greatly appreciated

I am looking at getting a set of rims that have 4.25 inches of backspacing. The rims are 17x8's and I have a 86 vert anybody know if this will fly? I also have a turbo coupe rear I want to put in but I am pretty sure they will not work with that right? Any help would be greatly appreciated

I am parting out a 87 vert for some stuff for my 86. I have a few questions as to what to take. Are the front brakes larger on the 87, also does it have larger A arms, the wheels seem to stick out farther on the 87. I don't know much about the car I just bought it and it was a 2.3 converted...