Search results

  1. M

    JRichker -- Rest in Peace

    Oh man. Sad to hear this. His crank no start checklist was a staple for me. He will be missed. God speed brother!
  2. M

    WTB/Trade Wtb: Yellow top injectors for 02 4.6

    As the title says, I'm looking for a set of yellow top injectors. These are going on my 02 expedition, not looking to spend a lot. I gave away my set from my fox like 15years ago... In League City, Tx
  3. M

    Mach 1 into GT

    No need for the mach ecu, you can use your gt ecu and a sct tune. The mach wiring harness is a plus because you will use your wiring harness but need to add some new connectors and lengthen some as well. Over all it a simple as hell swap, I did it by myself in the garage. Started pulling...
  4. M

    Wow i think i funked my car up

    Passenger side gasket should always be replaced, they brake so damn easy.
  5. M

    Back Pressure

    Car running rich?
  6. M

    SCT gurus, come on in!

    Well I think i just answered my question. I tried it out and i'm pretty sure it tuned it as a gt becuase it ran kinda funny. I wish there was a way to fix this damn speedo without needing $200 for a retune!
  7. M

    The story of a 2 Valve Carb Conversion

    Ever seen "The Perfect Storm" ? lol Scary ****! Good luck on the carb mod but honestly i would try and find the problem with the fuel injection b4 you go and spend money for a carb setup. could be something really simple you AND FORD missed. Even if you had to buy a new computer thier not...
  8. M

    Front brake job.. What went wrong???

    Did you have to "push" The caliper pistons back in a little for the caliper to go over the new pads? You have a 2003 model right?
  9. M

    SCT gurus, come on in!

    Ok I have a 02 GT that i swapped an 03 mach 1 engine into using the original GT computer and wiring harness. I had the car tuned with an sct x3. On the third dyno pull during tuning the sct tuner crapped out, so my tuner gave me a new sct tuner. Because of this i lost my "stock" GT tune and now...
  10. M

    Bleeding ABS system...

    according to the website you have to use a scan tool. Which , I already knew. I was just hoping there was a "hack" or something, like a way to jumper two wires to activate the system. I was hoping to do this at home, but... On the other hand i may have access to an NGS tool through a...
  11. M

    Bleeding ABS system...

    Yes i bled the master cylender. Thanks for the link, I'll check it out.
  12. M

    Bleeding ABS system...

    Ok, When i bought my 2002 GT it had some probs. One of the first i noticed was the drivers side rear banjo bolt was almost all the way out. Fluid was leaking everywhere. I trailered her home, and tightened it up. I bled the brakes and MC with a one man bleeder kit till there was all new fluid...
  13. M

    What might this smell be?

    bad catalyst converters have been said to have a rotten egg smell.
  14. M

    Wheel studs for Moser 31 splines

    Just picked up some new Moser 31 spline axles and a cobra trac-lock :D I need to get some new wheel studs to go with the mosers and want to get a good set of 3 in. studs for them. I'm not for sure but i think i have picked out the right size and thread (1/2-20 RH in.) and press in...
  15. M

    Ball socket/drivers side exhaust leak

    No spacers on mine. I just looked at my old sohc manifolds and they have the same "shouldered" studs on them. nyuk98gt- Have any pics of those "trumpet bell" inserts?
  16. M

    Ball socket/drivers side exhaust leak

    I'll check on the trumpet bell tommorow, but one pipe is slp (X) and one is BBK (H) and both are doing this. The drivers side studs DO have shoulders on them. I was thinking about trying to get some studs without them or get some bolts and thread them through the manifold holes. Thanks for...
  17. M

    Ball socket/drivers side exhaust leak

    I would rtv it but the problem is that even with the bolts completly tight it's still able to be moved around a little on the flange. I took the x pipe and had to cut it since the previous owner welded the joints instead of using the clamps, I then took the drivers side piece and bolted it up...
  18. M

    Ball socket/drivers side exhaust leak

    Anybody?
  19. M

    Strange smoking problem

    Deleting the PCV isn't necesarily the best idea though. See if you can fab some baffles to work in the valvecovers. Possibly...Header evac time.
  20. M

    Ball socket/drivers side exhaust leak

    Well I picked up a used SLP o/r X to try out, so I installed it last night along with a new clutch cable. This is on my 2002 GT with Mach1 motor. Today when i drove the car I realized I needed to adjust the cable a little. So up the car goes on jackstands. I'm under the car with it running...
Top Bottom
Back
Forums
Menu