Search results

Alright everyone claims you can’t fit 15” rims over cobra rear brakes without really expensive rear wheels or tons of positive offset. I am planning on upgrading the brakes on my LX and printed off some of the different templates that Baer has on their website for wheel fitment. Here is a...

Trying to figure out the fox body motor mount hierarchy… According to the sticky, the prothane unit is .5” taller than the Energy suspension unit and reading elsewhere the stock hatch/notch mount is .5-.75” taller than the stock vert unit. How do the aftermarket units compare to the...

I have the "taller" Prothane motor mounts on my car and need to drop the engine down about .5-1" for hood clearance. I was just planning on picking up a set of the energy suspension units, but then I notidiced the PS hardline running to the rack is less than .25" from the oil pan as is, if I...

Do any local (greater seattle area) stores/shops/warehouses/etc. stock canton products? I can't think of any off the top of my head. looking for a dipstick part number 20-850. PM me if you feel uncomfortable replying to this post

All right, on my 94 cobra the rad fan decided to quit working recently, so she likes to overheat. I checked the stupid simple stuff (mega fuse under the hood, and replaced the engine coolant temp sensor). Before I start actually diagnosing it, is their any other stupid simple stuff off the...

A couple of years ago (mid 2005) my buddy’s brother came into town and rented a car. When we was filling out the paperwork they asked him if he wanted to upgrade to a “sports car”. When he asked what it was they replyed “Mustang GT”. So for only a few bucks more he drove around in a 2005 GT...

nevermind, mods delete

On my 88 lx I am prob going to need to deal with the speed density issue soon. I was thinking of getting a tweecer for the SD since they offer it now. Is it a diffecent part number than the mass air tweecer (ie if I later convert to mass air do I need to get a different tweecer or upgrade)...

I found this on another thread, and would love to see his wiring diagram thanks

wondering what years/makes/models came with SMALL CASE 3g alts, so I can narrow down my search at bit. I have a sneaking susp that these will actualy fit an FE...

http://www.leftlanenews.com/2007/01/18/spied-2009-ford-mustang/

I am threatening to put a cobra trans T56 into a car that needs a mechanical speedo (67 cougar). From what I can tell to you can pay someone 300 bucks to convert it for you, but I hate paying someone good cash when I can do it myself. Anyone done this? Parts needed and where to get them...

I am threatening to put a cobra trans T56 into a car that needs a mechanical speedo. From what I can tell to you can pay someone 300 bucks to convert it for you, but I hate paying someone good cash when I can do it myself. Anyone done this? Parts needed and where to get them? Cost? Etc...

My Dad is threatening to buy a new Cobra as soon as they get down to MSRP, I have been doing some reading on the internet and it seems people are starting to pick them up for than now, so last Saturday my old man and I decided to stop by Bill Pierre Ford to talk to them about this. After...

I am threatening to put a cobra trans T56 into a car that needs a mechanical speedo. From what I can tell to you can pay someone 300 bucks to convert it for you, but I hate paying someone good cash when I can do it myself. Anyone done this? Parts needed and where to get them? Cost? Etc...

On the front page they have a “how to rebuild your ford 8.8 rear end” the top computer picture is of a GM posi unit. http://www.stangnet.com/Tech-Articles/1996---2004-Rear-End-Install-061215.html on top of that the article is pretty bad tech wise, with no mention of pinon depth, pinon...

Does anyone make Polyurethane or Urethane bushings for the upper control arm for 67 mustang/cougar? Despite what the Summit racing website says Prothane and Energy Suspension doesn’t make them I really really don’t want to replace it with factory low duramiter junky rubber bushings. If...

Is there any good suplier that sells the lower balljoint for a 67 mustang/cougar without the whole lower control arm assebley? If so part number/link/brand/etc would be helpfull, thanks

I am looking for a decent looking gauge pod that can hold three 2 1/16th gauges for my 88 LX. The triple gauge A-pillar ones walk that tacky line a little too closely for my taste, does any one has some other ones they like? Florida 5.0 used to make one that was sweet and mounted to the dash...

Ok so I went the mustang round up ride and drive at PR this last spring for the first time and had a blast. I am planning on doing more of those types of things. I noticed we didn't get any lap times, but I was wondering from other people that had run the PR course what times they were...