Search results

  1. Lsredy2kstang

    3.8 V6

    1999 came the 190 hp due to the split port design. Acually it was 2001 IIRC that has 191 hp.
  2. Lsredy2kstang

    Steering Wheel Replacement

    They are not standard torx. They have a point in teh middle, tamper resistant torx is what they are called.
  3. Lsredy2kstang

    Steering Wheel Replacement

    That exactly what it is a security bolt so that people that break into your car they cannot steal that 1k piece i n5 seconds. Go to the auto store and tell them what you need. They will have it.
  4. Lsredy2kstang

    need help ASAP!!!

    Dont do that. It does not sound like your starter if it will start then stop. Does it sputter? have you thrown any coded? Could be a bad coil pack, check your plugs lately, could be lots of problems. How many miles on the car? Could be clogged injectors
  5. Lsredy2kstang

    need help any advice would be nice

    have you changed your fuel filter? Sounds like it could be clogged.
  6. Lsredy2kstang

    need help any advice would be nice

    That is the FORD test port for FP. You can push it and see if you are getting gas up there. But if it starts then dies at idle i am assuming you are getting gas enough to start it.
  7. Lsredy2kstang

    need help any advice would be nice

    What do you mean pressure? WHen you turn the key to the on position you should hear the pump priming. Have someone stand behind the bumper near the gas tanks and you will hear it. If it cranks but not fire I would hightly doubt it is the fuel pump.
  8. Lsredy2kstang

    need help any advice would be nice

    My next thing to check would be to clean teh IAC. Idle Air Control. Either take it off and clean it with brake/carb cleaner well or change it out.
  9. Lsredy2kstang

    Is the factory intake tract all that ineffective

    The major restriction in the intake is the upper intake itself. If you look there are two bolt holes right after the throttle body that impead air flow. Yes a CAI would help some. And why not have a 13 sec car? I do and If I can make it to the track before they all close, I am hoping to drop...
  10. Lsredy2kstang

    v6 mustang timing problems

    YOu had to take the front accessories off thus the camshaft sensor. Are you absolutely sure you put it back the same way it came out. One tooth will make it backfire and have the ignition off. I know this for I did this as well.
  11. Lsredy2kstang

    good for engine shop around atlanta?

    Yes call MPH at 770-591-0000 they will be moving soon to a bigger establishment with the capabilities of Jeff Harris doing the pushrod stuff. he knows his pushrod's!
  12. Lsredy2kstang

    DRIVERSIDE MIRROR SHAKES

    It sounds as the bass in the radio is causing the vibration. Turn the volume down
  13. Lsredy2kstang

    Hello...I finally bought one!

    Hey Jenn, sic em would ya! You guys have no idea what you are getting yourselfs into!
  14. Lsredy2kstang

    i need a stock shifter

    Sarcasm is not a strong suit of yours is it? Maybe he does not do ebay. He should not post this in a talk section either. So both of you are wrong.
  15. Lsredy2kstang

    I need two calipers

    I kow that you meant ot put this in the Classifieds so I will move it for you.
  16. Lsredy2kstang

    Anyone looking a GT500 vert

    Innappropriate post. You have only posted here 4 times in the past since October 06. I am deleting it for this reason.
  17. Lsredy2kstang

    NOS

    I am throwing down 326/362 with DR, 8.8 and a posi. I guess I will be good to go into the 12's then. I will be able to get to the 1/4 mile soon, or I hope!
  18. Lsredy2kstang

    NOS

    You need to look again, even the commentator, 13.16 and you are correct, it is not a 12 but that was without the cam installed. That was a stock v6 motor (virgin) on nitrous.
  19. Lsredy2kstang

    NOS

    There is always one in the bunch that cannot believe that someone has done it. Here is a quick video of a 13.16 pass without the cam or the linelock. http://videos.streetfire.net/video/02febe35-81ae-47cc-8219-987d0064db5d.htm If you notice, the MACH1 beside me ran a 13.3
  20. Lsredy2kstang

    NOS

    You are right, I have some suspension upgrades, i have full exhaust upgrades, i have a cam upgrade with rockers and springs. I will be making some full 1/4 passes soon I hope. I wanted to go to FFW Bristol but I doubt that will work out.