Search results

Hey guys, its been a while since I've posted any questions on the site. I'm installing a MSD Launch Control, and I have it mounted in the glove box. Just wondering if there are any holes or grommets on the passenger side firewall that I can route my wires through.

I know that you can no longer get a bezel for the SCT 4-Bank Eliminator Chip. Has anyone come up with any other product that works? Best I could find was a BDC switch, which is a pushbutton switch showing the numbers.

I'm putting a new engine into my 89 mustang. I have a 7qt oil pan (proform) which i will be installing. I also ordered a canton dipstick which needs to be calibrated. My question is do I put a total of 7qts of oil in the car, or do I need to compensate for the filter? My haynes says the...

I know the performer rpm heads do not have provisions for emissions, but I wanted to know if I can still run the cats in the h-pipe or do I need to pick up an offroad h-pipe without cats. thanks in advance

I just installed the fiore firewall adjuster and quadrant, bit of a pain to install - actually getting the old quadrant out was the biggest pain. Anyways - I have everything tuned great right now - but i am just about to install the Freeplay kit and I was wondering if I will need to re-tune the...

I replaced my dash a couple months ago, and recently I noticed I was running really low on oil and my check oil light didn't come on. I'm wondering if I might have jarred the bulb loose on the back of the dash panel. When you turn the key in the ignition, does the check oil light come on...

I am installing gauges in my glove box and was hoping to have the new gauge lights come on when I opened the glove box (with the glove box light). There are 3 wires going to the glove box light/switch. 2 yellow and 1 black. Does anyone know how this switch works? why is there 2 yellow. I am...

I was sent the wrong swaybar, its meant for 94 and up. I have an 89. Does anyone know what the difference is?

I want to make sure I got the correct front swaybar. I ordered Eibach 3510, but the box and bar both say 3518. The bar fits on no problem. does anyone know if the 94 and up swaybar look similar, or are they completly different? I have a couple photos posted...

I ordered an anti-roll kit for my 1989 and i think I got the wrong one. If someone has one installed on a 1994 and up please look at the following pictures and tell me if you have the same bar. thanks

I need to know the measurement from ground to fender lip. I have quite a bit of stereo equip in the trunk, so as a result the back end sits a little bit lower than the front. I just picked up a front coilover kit and I want to know how low I can go in the front. My rear measurement is 25.5"...

I thought I would post this for anyone in the future. For several years I have failed my emissions test, and used to get by with a conditional pass. this year I pickup up a used MAC hi-flow H-pipe with cats for ebay for just over $100. It made a huge difference in the results and my car...

I have alot of movement in my rear end. I have the mac upper and lower control arms installed and I'm looking for a panhard bar to control side to side movement. Has anyone tried the HPM panhard kit? Will it work with aftermarket control arms? any input would be much appreciated.

Does anyone have a jacobs mastermind hooked up to a NOS 05115 dry kit? I just wanted to know what solenoid I should hook up the Jacobs trigger (blue) wire to? I have it hooked up to sol 1, so that when it pulses the fuel pressure regulator should be able to adjust the fuel accordingly. If I...

I just ordered a jacobs mastermind and was hoping someone who owns one could go out and measure it for me. I need to know if I have to pick up another cover for the console (that holds the stereo and hopefully the mastermind) If anyone can help that would be great. thanks again.

my brake pedal is pretty hard to push down. its been like that ever since I can remember - problem is I don't know what normal is anymore. I've got all new brakes (mm brake upgrade kit, new mc,.......). I know fox brakes are known to be pretty bad, but mine seem a little worse than that...

my car's oil pressure seems to drop when the engine gets warm. It usually dips pretty low at idle and then bumps back up when I give it gas. I've replace the sender. the car has over 300,000kms. How low can your oil pressure drop and still be safe?

I'm looking for some black interior pieces, inclucing black kick panels and black arm rests. I'm sick of painting them. I've tried every paint, primer, prep possible and still the paints just don't hold to some of the plastics in the car. Other plastic inclucing the center console came out...

I've read a million posts on how to replace the door pins and bushings, but does anyone know how to replace the roller bushing? thanks in advance.

stupid question guys, pardon my ignorance but I removed both caliper to replace them and now I'm not quite sure which is left and which is right. they both will fit on, I'm imagining the bleeder points straight up? thanks again the rebuilt calipers have ford part number 355L and 406R...