Search results

Selling a like new set of BBK cermaic coated shorty unequal length headers made specifically for 1994-1995 GT 5.0 mustang but may fit others as well. Comes with the boss fitting for emissions fitting. These were used on dyno runs only for a motor. They have no discoloration from use at all...

Just installed my wideband Aem kit, it looks nice & I hope I can figure out what the deal is because the online forum on the AEM site is apparently not manned, no one seems to answer questions on their products. Here's my question: I have stock 5.0 motor, stock injectors, only intake add on is...

I have a choice between a powedyne BD10 supercharger set up or a 2006 Kauffman car hauler or a Vortech V2 supercharger set up for 99-04 mustang. Car hauler would be only an occasional need Powerdyne BD-10 is crap I have heard Would need quite a few bolt ons for the 99-04 Vortech to fit my...

Someone else can chime in but to my knowledge they are not 100% interchangable, the wiring harness doesn't match up, not sure if if lose anything else but the tach I know will not be functional fro a 96 in a sn95 car. Bill

Well I just replaced the pip snesor on my MSD pro billet, I was forced to do so because some jackass cut off 4 of the wires on it to put a 3 wire connctor on it, I didn't notice the change when I bought it. the biggest PITA is getting the gear back on in same exact position it was so the rollpin...

Just use some grade 8 bolts & nuts with lockwashers they are more HD than j-clips anyways. If not send me a PM I know I have some j clips off my 95 as I used bolts & nuts on mine when I changed out the lower control arms. Bill

OK guys I have a 95 Gt that I am building as a Saleen clone nothing real hard core yet but have spent tons & continue to up grade & have a few questions. I just installed new Upper & Lower Mac rear control arms & BBK subframe connectors, Kenny Brown shock tower brace & strange 10 way...

I have a 1995 gt/ Saleen clone I have been building on for quite a while now picking up parts as I find them. I have been looking at headlights as next upgrade. Can you install cobra headlights on a GT? They seem to look better than stockers & less cheesy than the JDM's etc. If anyone has...

I purchased a 100 pc screwdriver bit assortment online for $15 has every type bit you could think of in it. Even one for wing nuts.

I ran into same problem it has to be the flywheel. I ran into this with a c4 conversion on my 90 coupe. Double check the flywheel gaurantee you have large bellhousing with small flywheel. Bill

Give us some background on setup. What have you changed besides the motor? Injectors, mass air meter, etc.. could be a number of things based on description anything would be a guess.

Well I only have 1 set of the inner mesh pieces, as a matter of fact if you have to remove them be carefull they break off the plastic tangs very easily as I did to one side already, had to glue it back in. I like the looks of the black but do not think it will be a look I will like long term so...

I am having a tough time deciding which hood inserts to use on my Saleen clone car. I have the original inserts that have been painted yellow same time as car with black plastic mesh. I purchased some green inserts painted them black semi flat same as hood in center. I think it looks good either...

You should break down & get a gauge to read pressure with an Adj fuel press regulator you dont know what you are setting it at without the gauge. I think maybe you have injector issues. I know when my motor sat for a couple weeks they stuck open car wouldnt run even with what I felt was good...

well I guess its going to have to be the whole assembly purchased. I saw where you could buy window reg. repair kit & other minor part kits so I figured on maybe a source for seat track parts.

Ok I will say the obvious I know I can get a used power seat track from junkyard etc. I took mine apart to find out why it wasn't working. The motor & the small square flex shafts are fine, the plastic drive gears inside the left & right tracks are broken into many smaller useless pieces. I was...

Just curious if you are looking at the engine when raising the throttle or if you are in the drivers seat? It is more than likely the pressure plate torqued unevenly or out of balance or like someone else stated wrong weight on it. If balancer were bad the engine would have been raising hell at...

Just be sure to take loose the starter while your head is not under it! I know I only say that because I left my head in the way, I had the little red dot of india in the middle of my forehead for a week! My buddies could not resist all the joking. It is easy to do especially if the starter is...

Fabfordtech the standard knob for the ford shifter is metric 12mm X 1.75 my guess is the pro 5.0 shifter being usa made is more than likely SAE threads. I have a lathe in my home shop I could bore out the knob you have now & bush it for whatever thread you need. Would be way less expensive than...

Could have a bad connection causing it to get to hot, or shorted out wire. I went thru 2 before I found out connector was bad on mine, I just pulled one off junker at salvage yard. Bill