Search results

i have a carb 302 that i converted to efi. it has a centrifugal supercharger. how do i run my pcv system. there is a rubber grommet in each valve cover. do i just stick a pcv valve in each valve cover and run them both to a vacuum source??

i am installing a t-5 in my 5.0 mustang and i am going to install the new clutch and i noticed that the outside edge of the pressure plate is about 3/8" away from touching the flywheel. is this normal? i can run in the bolts to make it contact the flywheel but they feel too tight and actually...

how would i wire an autometer speedo in a 88 mustang?

i have a long list of parts i need to sell here is a link to the post i have on craigs list 65-68 mustang parts for sale

i have a 65 mustang with a 302 & AOD trans. I want to know if i buy a stock replacement exhaust system will it fit? I know the AOD is bigger but i don't know if it will clear it or not. Thanks

I have a 68 powersteering setup on my 65 and I have shorty headers. 90 degree part of the pressure hose out of the back of the pump hits the headers. Has anybody ran into this problem and what have you done to fix this thanks for the help

I just bought an 85 302 H.O. mustang engine from my friend and i have it all together but i can't find any sparkplugs that fit it. I bought the autolite 25's but they won't thread in. Does anybody know what plugs this engine gets????

I have a 65 mustang with a 85 302 with an AOD transmission. I need to know how can i tell with the starter installed can i check for the teeth meshing with the flexplate teeth to see if i need more or less shims in it?? Also how would i wire it with the stock starter selnoid?? Thanks

This might sound like a newbie question but what side of the waterpump does the timing pointer go on. If anybody has any pics that would help too. Thanks

I have 2 edelbrock carbs on my 65 mustang and the throttle rod that connects the petal to the carbs is too long. If someone has a picture of their dual carb setup would help out a great deal thanks all!!

i just bought pre bent fuel lines from npd for my 65 mustang and i can't figure out how they route around the engine. If anybody has a picture of how the lines go under the car and in the engine would help a lot. Thanks

I have a 65 mustang and it never had brake/fuel lines on it since i hade:bang: it and i need a picture of the under side of one to see how everything is routed. Thanks for the help!

I have a 65 mustang with a 68 8" rear axle. It didn't have any drums on it when i got it and I don't know if I can get the 10 x 3/8" or the 10 x 2" drums. I would like to get the 2" drums but I don't know if they will fit. Any help would help alot.

i have a 65 mustang and i took off the parking brake handel off before i sent it out for paint and now i can't figure out how the cable runs through the firewall. If anybody had a picture of under the dash where the cable goes through that would help a bunch. Thanks

Is there someone that sells new sector shafts and wormgears for the 65-73 mustang steering boxes? Or do I have to buy a completely new one? Thanks:bang:

I was off work today so I thought I would put a couple of questions that I had up on here. does anybody sell shifer linkage that will fit my stock floor shifer and that will connect to my aod? I know Ron Morris sells one but is $140. :jaw...

I got a flaming river tilt steering column but my gearbox is shot. My question is does it matter if I get a new gearbox that has the long saft or the short one? I know I have to cut the long shaft shot but I don't know if it has to be cut longer than the shorter shaft gearbox. If that makes...

I just got the dual quad kit from summit for my mustang and I want to know why did one carb have electric choke and one manual? The other question I have about this is where do I hook all my vaccum lines up to. Thanks for all the help

I am selling my 65 mustang it has new doors, fenders, 1/4's, floors, trunk floor, wheel wells (inner & outers), rocker inner & outer on drivers side, 68 styled scoop fiberglass hood, shock towers, ect............. It needs paint all the metal work is done. I have taken all of the rust off this...

:bang: does anyone sell repro metal for the roof brace for a coupe 65 mustang?? The part that is inbetween the rear window and the 1/4 window. I don't know how else to explain it sorry. :bang: :bang: :bang: :bang: