392/393 Stroker and other Misc Parts

Discussion in 'Drivetrain Parts' started by maverick1099, Mar 8, 2010.


Find More Mustangs For Sale!

  1. maverick1099

    Founding Member

    Joined:
    May 18, 2000
    Messages:
    445
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Santa Barbara/Bay Area, CA
    All items are located in the San Francisco Bay Area, CA. I am willing to ship the smaller items at the buyers expense. Shipping the larger items will require the buyer to figure out how to get that done as I do not have experience shipping items this large. If there are questions on any items let me know. If you have a specific photo request let me know and I will post it up here.

    Here I have listed the components in this motor. It has about 5k miles on it and was in perfect running order when I removed it from my mustang. I have stored it completely covered and protected. Motor has $8-$10k invested in it but my new project does not allow me to use it. I will entertain reasonable offers. I am not looking to part it out at this time.

    393/392 NA Custom Built Motor
    [SOLD] Chromrmoly Oil PU
    [SOLD] Accufab 75mm Throttle Body
    150A Alternator
    [SOLD] Push Rods
    [SOLD] MSD Distributor
    [SOLD] FMS Flywheel 50 oz
    [SOLD] ARP Valve cover Studs
    [SOLD] 351 Accessory Drive Bracket
    [SOLD] TFS 351 EFI Intake
    [SOLD] AFR Heads 185 (mild port work)
    [SOLD] ARP Head Stud
    [SOLD] Crane Hydraulic Roller Lifters
    [SOLD] Crane 1.6 Roller Rockers (stud mount)
    [SOLD] Meldon High Volume Oil Pump
    [SOLD] FPS Balance 393 Stroker Kit
    [SOLD] Eagle 4340 H-Beam Rods
    [SOLD] Girdle
    [SOLD] Probe 4032 Alloy Pistons
    [SOLD] Clevite-77 Bearings
    [SOLD] 4340 Crankshaft
    [SOLD] 351 Block
    [SOLD] ARP Oil Pan Bolt Kit
    [SOLD] Timing Set 351
    [SOLD] Custom Ground Cam (Ed@FTI)
    [SOLD] Pro-M 80mm
    [SOLD] 42lb Injectors
    [SOLD] Moroso Oil Pan

    Pictures
    More Pictures

    I have a Lakewood bellhousing that I used on a 351w block. It is SFI but I believe that rating has expired. I would like to get ~$225 for as they go for over $400 new.
    I have the pivot ball, fork arm and throw out bearing as well. As you can see in the picture I have not ground the edges down.


    Pictures

    [SOLD] I have a ford 9" rear end. This came out of a 1967 mustang. It rotates freely and appears to be in working order. I have not personally run it in a car. Other than needing to be cleaned up it appears to be in good shape. I would like to get $300 for it but I will entertain all reasonable offers.

    9" Rear End Pictures

    I have a ford 351W block that is bare. I believe that it has been bored over 0.030" on the bores already. I have not run it personally as I already have a 351W based motor and as such I have no need for this additional block. I would like to get $150 for it but I will entertain all reasonable offers.

    351 Block Pictures

    I have a box of misc stock 1987 mustang GT parts. $25 gets all the parts in the basket.

    Pictures

    [SOLD] I have a complete set of 8 ford 30lb fuel injectors off of a mustang. These were in complete working order when removed from the car and have been stored inside since that time. I am looking to get $150 for them but reasonable offers will be entertained.

    Pictures

    I have a PRO-M 75mm Bullet MAF. It is the chrome variant and tuned to 30lb injectors. This came off of my mustang and was in complete working order. I have stored it inside since that time. I am looking for ~$100 for but I will entertain reasonable offers.

    Pictures

    I have an MSD 6BTM up for sale. I would like to get about $200 for but I will entertain reasonable offers.

    Pictures

    I have a Ford 302W short block out of a mustang 5.0. It was in perfect running order when I removed it from the car to put a larger motor in. I am looking for about $250 for but I will entertain reasonable offers.

    Pictures
     
    #1
  2. maverick1099

    Founding Member

    Joined:
    May 18, 2000
    Messages:
    445
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Santa Barbara/Bay Area, CA
  3. maverick1099

    Founding Member

    Joined:
    May 18, 2000
    Messages:
    445
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Santa Barbara/Bay Area, CA
    The 30# injectors have been sold
     
    #3
  4. maverick1099

    Founding Member

    Joined:
    May 18, 2000
    Messages:
    445
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Santa Barbara/Bay Area, CA
    I am going to start parting out the 393...
     
    #4
  5. BAD STANG

    BAD STANG New Member

    Joined:
    Mar 22, 2010
    Messages:
    14
    Likes Received:
    0
    Trophy Points:
    0
    how much for the heads?
     
    #5
  6. maverick1099

    Founding Member

    Joined:
    May 18, 2000
    Messages:
    445
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Santa Barbara/Bay Area, CA
    Bad Stang:
    You have a PM
     
    #6
  7. maverick1099

    Founding Member

    Joined:
    May 18, 2000
    Messages:
    445
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Santa Barbara/Bay Area, CA
    Weekend update of sold parts
     
    #7
  8. maverick1099

    Founding Member

    Joined:
    May 18, 2000
    Messages:
    445
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Santa Barbara/Bay Area, CA
    Update with more weekend sales
     
    #8

Share This Page