Need (but can't find) Idler Pulley

Discussion in '1994 - 1995 Specific Tech' started by dsg02, Dec 3, 2003.


  1. KeithStang

    KeithStang New Member

    Joined:
    Jun 17, 2003
    Messages:
    143
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Redding, CA
    UPR is selling a nice shiny billet one for around $70 if your into that bling bling thing. :flag:
  2. David R

    David R New Member

    Joined:
    Dec 21, 2002
    Messages:
    257
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Ohio
    Pep Boys had one in stock when I needed one.

    It was just identical to the stock one.
  3. QCStang

    QCStang Founding Member

    Joined:
    Mar 29, 2002
    Messages:
    899
    Likes Received:
    15
    Trophy Points:
    18
    Location:
    Aylmer, Quebec, Canada
    50resto sells them for about $20.
  4. Kdizzite

    Kdizzite New Member

    Joined:
    Sep 13, 2003
    Messages:
    294
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    West Bloomfield, MI
  5. Green 94 5.0

    Green 94 5.0 Founding Member

    Joined:
    Mar 25, 2002
    Messages:
    2,593
    Likes Received:
    5
    Trophy Points:
    49
    Location:
    Ft. Lauderdale, FL
  6. rockin_rick

    rockin_rick Member

    Joined:
    Oct 10, 2003
    Messages:
    972
    Likes Received:
    0
    Trophy Points:
    17

    Hmmmm. I ordered one, but have not used it yet. Maybe the bearing is bad.

    I asked about this in a thread and it was 2-0 in favor of it. I'll try again to see if I can solicit some more opinions.

    Rick
  7. snakeIs

    snakeIs Founding Member

    Joined:
    May 19, 2001
    Messages:
    828
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    With Your Girlfriend While you look at this stuff!
    Running without the idler pulley is not such a good idea, its there for a reason, at high rpms it keeps the belt from deflecting and resonating. Have someone rev your car to about 5 grand and stand out there and watch it.....I bet it bounces up and down like crazy!

    All I did was go to a bearing supplier and buy new bearings for both my idler and tensioner pullies, they both use a very common and cheap 6203 bearing that I paid like 5 bucks for both..and then you just press the old one out and the new one in, SIMPLE.
  8. 94GTLaserRC

    94GTLaserRC Squint as you approach, lest you be blinded by my

    Joined:
    May 7, 2002
    Messages:
    11,183
    Likes Received:
    5
    Trophy Points:
    79
    Location:
    Ernan Says "here it comes... dushbag"

    :shrug: That seems strange. Shoot him a PM (from Corral.net) He exchanged a PS pulley for me because it slipped off..:nice:

    RC
  9. KeithStang

    KeithStang New Member

    Joined:
    Jun 17, 2003
    Messages:
    143
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Redding, CA
    speedworx.com has that pully and the power steering pully both in billet aluminum. The idler is around $80 and the power steering pully is $180. Yes, I think those prices are very steep but, just putting the info out there. :flag:
  10. wazee

    wazee New Member

    Joined:
    Jun 3, 2003
    Messages:
    16
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Jacksonville, Florida
    a whoosing noise, did you install it backwards? Only three people have had problems with my idlers, One bolted the pulley on backwards and locked it down to the bracket and the other two put them on the wrong vehicles, go figure. The snap ring faces forward. Anyway it would be proper to address the problem to me directly instead of me running across it in a forum. my email is [email protected]
    cell # is 904-591-5803 (btw:1/14/03 phone charger is lost, should be up and running 1/15/03
    Customer service is still around. Here is what I mean:
    If your idler is not what you expected and it is my fault, send that thing back and I will replace it. just pay ship. I have yet and I mean I have yet to find a bad idler to this day that was due to manufacturing problems, only due to incorrect installation, and/or bolting it to a chevy! But, trying to be humble, I will give anyone the benefit of the doubt and make good on any mistakes.

    Mike W.
  11. 94GTLaserRC

    94GTLaserRC Squint as you approach, lest you be blinded by my

    Joined:
    May 7, 2002
    Messages:
    11,183
    Likes Received:
    5
    Trophy Points:
    79
    Location:
    Ernan Says "here it comes... dushbag"
    Hey mike...[​IMG]
    'bout time you pass by around here!

    RC
  12. wazee

    wazee New Member

    Joined:
    Jun 3, 2003
    Messages:
    16
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Jacksonville, Florida
    I have been busy lately, I just expanded my pulley business to other vehicles and more cool parts. they should be out in the next few weeks.
    ;)

Share This Page