Nodular posi 9 inch, disc brake 9 inches, wheels, and hoods

Discussion in 'Engine and Power Adder' started by 68coupe351, Aug 13, 2007.


  1. 68coupe351

    68coupe351 New Member

    Joined:
    Jan 27, 2006
    Messages:
    34
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Rockwell City Iowa
    I have the following for sale.

    1 -Nodular 9 inch center section with posi. 3:50 gear is pited but i have another 3:50 gear set in box. This center probably needs rebuilt. MAKE OFFER

    2 -I have two disc brake 9 inches out of bigger cars. If i remember right they have 3:00 gears. $200 a peice

    3 -One 9 inch out of a 78' ford pick up. 3:00 gear i think. $50 takes it

    4 -One chrome 87-93 pony wheel. has good center but chrome on wheel not great-probably driver quality. MAKE OFFER

    5 -Set of four 2000(if i remember right) 16" Mustang wheels. I think they are for a V6 but i have seen a set on a GT. Have driveable BFG comp TA tires. Have all centers and wheels have no rash. $250

    6 - 68 turn signal hood. No rust. no signals, just hood. had pins but have been welded shut. It may be slightly tweaked. MAKE OFFER

    7 -68 turn signal hood. RUSTY but is complete. May be useable just to plug the hole. MAKE OFFER

    Please make me a reasonable offer. I am interested in trades- let me know what u have. I am looking for a short shelby hood to fit a 67-68. Thanks, Lance email- [email protected]
     
    #1
  2. 68coupe351

    68coupe351 New Member

    Joined:
    Jan 27, 2006
    Messages:
    34
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Rockwell City Iowa
    Im located in Rockwell City Iowa near Fort Dodge
     
    #2
  3. bnickel

    bnickel Founding Member

    Joined:
    Aug 21, 2002
    Messages:
    5,642
    Likes Received:
    0
    Trophy Points:
    77
    Location:
    lubbock, texas
    just FYI, the big car disc rears are probably 9-3/8" rearends, the housing will work for a 9 inch but none of the rest of it will and they only came with 28 spline axles. i'm betting they came out of a mid 70's lincoln MK series car, if that's the case they are definitely the bigger 9-3/8 rear.

    again just an FYI
     
    #3
  4. 68coupe351

    68coupe351 New Member

    Joined:
    Jan 27, 2006
    Messages:
    34
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Rockwell City Iowa
    could be but the one tag reads that it is a nine inch?
     
    #4
  5. bnickel

    bnickel Founding Member

    Joined:
    Aug 21, 2002
    Messages:
    5,642
    Likes Received:
    0
    Trophy Points:
    77
    Location:
    lubbock, texas
    does it have a 5x5 bolt pattern or a 5x4.5 pattern, if it's the 5x5 pattern it's more than likely a 9-3/8 if it's the 5x4.5 pattern then it's likely a 9 inch.
     
    #5
  6. Rusty67

    Rusty67 Well-Known Member

    Joined:
    Dec 3, 2002
    Messages:
    3,616
    Likes Received:
    13
    Trophy Points:
    59
    Location:
    SB, CA
    1 -Nodular 9 inch center section with posi. 3:50 gear is pited but i have another 3:50 gear set in box. This center probably needs rebuilt. MAKE OFFER

    Do you know how many spline this piece is ?
     
    #6
  7. 68coupe351

    68coupe351 New Member

    Joined:
    Jan 27, 2006
    Messages:
    34
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Rockwell City Iowa
    i assume 31 but i will check
     
    #7
  8. 71 Mach

    71 Mach New Member

    Joined:
    Mar 7, 2007
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    0
    Are any of the 9 inch rears a posi and will they bolt into a 71 Mach. very interested.

    Thanks, Jesse
     
    #8

Share This Page