Search results

this is a new aeromotive 340 stealth tank, new... Box is open but never installed or used. Tank has internal fuel pump for carburetor or fuel injection applications. Sender is the correct ohms for the factory ford gauge . Selling because the 4 link i installed requires a modified tank and didnt...

Up for sale is a currie 66 mustang 9" rear with track 9 31 spline axles and fill/drain Complete explorer brakes with internal parking brake Cast iron center section with aluminum daytona support, 4350 yoke, detroit soft locker, 4:11 richmond gears Caltracs 2 hole adjustable traction bars...

Ford toploader 4 speed, good condition. Has small block input shaft installed also have bigblock input shaft. Includes hurstshifter. Asking 400.00 located in long island new york.....will have pics posted momentarily Email [email protected] if interested

It doesnt really matter

My exact thoughts. This isnt the first cage I ve done. Having done several, and looking at my car (with complete cowl out) I don't see any major conflicts. My most difficult challege will be snaking the "strut bars" through the firewall and over the heater box but I think it can be done. Thanks

Well, carefully looking at it, I have what appears to be a straight shot down very tight to the "A" pillar. From there, I can extend front bars to support my frame (towers are gone). My upper and lower cowl is out so I can also reach in through the top which would allow me to hide a dash bar as...

Anyone please?

Does anyone here have pics of a behind the dash roll cage ina 66? I am planning on a full cage but don't want to place the "A" pillar bars in front of the dash. Looking at my car, it appears that I can keep them tight to the body and squeeze them between the dash and heater box. Any pics or...

I have a MII frontend in my car and never bought the heidts sway bar kit, at least as of yet. I do have a new performance sway bar for the factory front and and was tossing around trying to make it work. Anyone else out there use a swaybar other than the Heidts specific bar? Thanks

I have a new 66 power centerlink, 75.00 shipped. This also may fit a 65 but I am not sure if there is a difference or not. It will definately not work with a 67. If interested email [email protected]

I have a 1965-1966 empty 9" housing (52") 200.00 obo Also Granada spindles and backing plates 100.00 obo The parts are in NY. I did a shipping estime for the housing from NY to CA and it was about 40.00. Email [email protected] if interested

Why does it seem as though the tire sticks out on the passenger side and sits right on the driver side?

I am just about to do a tko 600 in my car in the next week or so. I just did a mustang II front end. I gotta get my cleveland mounted up first and plan to use my toploader and stock mount to get the engine right. Then I figured I would just cut the tunnel where the two access covers are on the...

Nothing except another tube tying down to the torque box on each side

I love the new front end but just do not trust the flimsy frame rails. I have been thinking of running 1-1/4" tubing from the firewall past the suspension and then bend it down to the frame following the contour of the previously removed shock tower. I have also been tossing the idea of running...

Mustangsandmore has an article a guy did using a latemodel crossmember and cutting the tunnel. IMO, he cut too much tunnel. One of the members here had a pictue with the shifter sticking through the stock hole and cuts only where the two access covers are on the tko. Other than that, you are on...

I am just curious if anyone has done the MII front end and a 351 cleveland. I just finished my front end and am gonna get the motor ready for mounting. It already has a fox body pan built by moroso. My concern is clearance with the crossmember/rack vs oil pan. Obviously its propably something...

There is some sort of retaining ring. I have not had much time to physically do the work yet. It isn't like a snap ring but still may work. I also need to see if it would be an issue once the wheel is mounted and the steering linkage is hooked up. Right now, my biggest concern is whether the oil...

I am in the process of modifying my stock column. What I had found is a piece of structural tubing that is 2" od and 1-5/8" id. From mcmaster Carr I got a flanged, sealed bearing that fits into the structural tube. My plan is to weld this piece of tube into the shortened steering column tube. I...