Search results

Has anyone ever bought from California Mustang (www.cal-mustang.com)? If so could you give me any insights into your experiences with them? Thanks

sent you an email

Ok, got out and took the stang for another drive today. The tranny fluid was fine, maybe even a touch high. I was still have a problem with it slipping from 2nd to 3rd and even a couple of times from 1st to 2nd. I talked to the previous owner and he said that he never had any problems with...

Well, that about sums it up. I did notice some transmission slip when it would shift into 3rd, but other than that it drove great. So heres my tech question, are there any internal seals that could degrade over the 16 yrs that could cause it to slip only when shifting into third? I did fill...

Check out this thread: http://forums.stangnet.com/showthread.php?t=667942 its on this forum. IMO yes it is large enough to weld anything on a mustang, the frame rails on a stang (to my knowledge) are less then 1/4" thick so you should be fine. As far as wire selection and what it will...

The Tractor Supply company here in the Kansas City area has a HOBART™ HANDLER® 140 WIRE FEED MIG WELDER for $449.98 (TSC # 3812040) new. I would spend the extra $50 for a new than a reconditioned (if you have to pay for shipping the $50 is worth it IMHO). As far as thickness Tractor supply...

65stang200, Yes it was your post that I saw. It got me thinking about linkages and what not. I think I have an idea in my mind on how to set it up to run at different rpms. The only thing I dont know is if air would get sucked in from the other two carbs or if it would get blown out from...

Okay guys heres my question for the day. But first my setup: 200 ci I6 bored 30 over, valve job, cam from FSPP (ARC 268 or something similar), new rockers and springs, double timing chain, 2 1/4" dual exhaust with new header, keeping the c4 for now but will change over to a T5 and a MSD or...

Thanks for the posts guys, thats alot of help. BTW the key that the previous owner gave me did not work. So now I have to take out one of the door locks and take it to a locksmith for new keys. I am now 95% done with the electrical on the barn/shop and hope to finish up with it and get the...

I just got the key and the title in the mail today. :D :D Now I just have to finish the barn (pour the concrete floor, run electrical, run air lines and close the fourth side in with garage doors), should have that all done in the next three weeks. I've had to do alot more to the barn than I...

ps I will have to check on shipping cost

I will take the engine and rear end. Did it run when you got it? check my sign. for my website, it has my contact info on it.

Being that the block is only 200ci stock I didnt think I would be able to reach the 400 hp range. Maybe if I had a 250ci that could be possible but like but like 65shelbyclone said whats the upper limit? Mike from FSPP would probably know if its possible.

I am going to be putting up forms for a concete floor in one of my barns (40' wide x 28' deep) that I will use as a shop and I am wanting to put a car lift in one of the four bays. Does anyone know if they need any type of footing under them to support the wieght? And for that matter what brand...

Dejavu, I understand that the chassis will need to be upgraded, I have plans to stiff up the entire chassis with a tubular support system. Doing whatever I can to keep it concealed within the body and unseen because I want to keep the car looking stock on the outside. As to what I am going to do...

I just added two more pics to my website they dont give colors but I think its a lot better the the prev. pictures.

It says red into (from starting motor relay) and yellow out

I added a pic on my website, at the end I think this will help.

66Runt, does the T5z bolt straight onto the I6 200ci or do you have to get a new bell?

6T6coupe your correct about the chassis, I wasn't sure how much I should talk about this in this thread since the title of the thread is about increasing HP. As far as what I am going to do to the chassis I don't know yet. I probably wont have the car striped down to the frame for another...