Search results

  1. AZNEAL311

    WOT questions

    Ok I cleaned my airfilter,MAF ,replaced o2 sensors, checked the gap on the plugs. New ICM,MSD 6AL removed. Will stock ignition and a Blaster2 coil work with eachother? If I roll into the throttle slowly it will go great till theres only a little more pedal left maybe an inch give or take then it...
  2. AZNEAL311

    WOT questions

    When ever i go WOT my car falls on its face, doesnt matter what gear or rpm. If i want a decent launch i have to find a sweet spot in the throttle(a little more than 3/4). Anymore and she falls on her ass. Just replaced stock injectors with 24# with calibrated MAF, new holly 190lph fuel pump...
  3. AZNEAL311

    Engine starts, then dies

    Sorry forgot Forgot to let everyone know i fixed it a while ago. Turned out to be a bad computer. Replaced it and ran great.
  4. AZNEAL311

    Help with Fuel Rail install

    Thanks> Dont know what i would do with out Stangnet
  5. AZNEAL311

    Help with Fuel Rail install

    I just bought a set or billet aluminum fuel rails. It is just the rails and regulator. I bought the Russel adapters for Ford EFI to AN. the pressure side is 8AN and the return is 6AN.Is that right? Do the stock rails disconnect lower near where it turns into rubber as well as up near the...
  6. AZNEAL311

    FlyWheel HELP

    I just bought a stage 3 clutch with aluminum flywheel. The Flywheel came with both 28 and 50 oz weights. I know a stock 88 5.0 is the 50oz but ive also read stuff like strokers,306s or any thing with custom internals could have been balanced for 28oz. The guy I bought the car from didnt build...
  7. AZNEAL311

    Flywheel weights??

    What size weight? From what i read 5.0 H.O. use 50oz which is what I have but not stroker kits. The guy I bought my car from didnt build the motor or know much about it. I have the oil pan off right now and could see the SpeedPro symbol on the pistons so i would assume its bored 30 over. How...
  8. AZNEAL311

    Flywheel weights??

    I recently bought an aluminum flywheel and it cam with 2 different weights. It does not say any thing about them so I have no idea which one to use. Anyone have any idea?
  9. AZNEAL311

    Gripforce F1 clutch

    Yea I kind expected that. No slip in it at all. But I figure its a good deal might as well try it out.
  10. AZNEAL311

    Gripforce F1 clutch

    Well I have my engine out to replace my oil pump. Since it is out I figure I should do a few things to save me some trouble later on. Replaced the rear main oil seal with a teflon seal. I also decided to get a new clutch. Im looking at one from Gripforce. A stage 3 F1 rated at 550HP and 487...
  11. AZNEAL311

    Oil Pump Replacement...

    Same thing happened to me. I just got the motor out and on a stand last night. Pulling the engine out was not as hard as I thought it was going to be. Its a good idea to have some extra hands there. With the motor out might as well take care of a few other things. I am replacing the clutch and...
  12. AZNEAL311

    EFI Lift Plate

    Anyone in the Phoenix,AZ area know where to get a lift plate for EFI 5.0? Im finally going to have time to pull my motor this weekend and I am in need of a lift plate ASAP. Ive tried every where I can think of with no luck. I would normally just order one from Summit however I dont have time to...
  13. AZNEAL311

    Oil Pump Drive Shaft Pics

    ok update to the lost oil pressure issue. When I looked down the Dizzy hole the drive shaft looked good. I used a 1/4in ratchet to turn the oil pump just to make sure it wasnt seized. When I turned it i noticed the bottom wasnt seated in the oil pump. Then it dropped to the bottom of the pan...
  14. AZNEAL311

    Got a Monster Tach? come on in...

    I just got a 5inch autometer tach and was thumbing thru the instructions and noticed it says warranty void if hooked up to MSD ignition system. Is there a reason for that? Will it damage the tach? I have MSD Dizzy,Blaster 2 coil, and 6AL box.
  15. AZNEAL311

    Oil Pump Drive Shaft Pics

    Yea I have other issues but who doesnt with these Fox bodies? But they are more than worth the trouble thats for sure. Will just turning the motor over with the starter enough to build pressure? I dont really want to start it with out oil pressure. Also i heard from some where, maybe here maybe...
  16. AZNEAL311

    Oil Pump Drive Shaft Pics

    Yes it was making noise fitting the pissed of sewing machine on roids. Before this problem I wasnt burning that much oil between changes. Only after the rebuild did it start consuming oil at a higher rate. I didnt really get many more miles on it to really tell how much. In the 300miles or so...
  17. AZNEAL311

    Oil Pump Drive Shaft Pics

    Oil Pump Drive Shaft I lost oil pressure a while back and am just now getting around to fixing it. I am not to excited about pulling the motor just for a bad oil pump. Ive heard so many different reasons as to my I might have lost pressure, from bad pump, drive shaft slipped out, blown block...
  18. AZNEAL311

    Notice to egg throwers:

    I loaned my 88GT vert. to my brother one night and woke up the next morning to my mom telling me to turn on the news. So I did and sure enough there was my car in an Apt. complex with all 4 tires slashed along with almost 50 other cars. Needless to say I was pissed. I wanted to not only kill...
  19. AZNEAL311

    No oil pressure

    I started the car and went to drive off and noticed a metallic grinding,rubbing noise. I checked my dash and saw no oil pressure so i shut it off. I popped the hood and noticed there was oil every where one the backside of the motor. Even on the hood,firewall,wires. It all seems to be coming...
  20. AZNEAL311

    Just installed pcv valve, cant get the engine to idle

    what about dumping the codes?