Search results

  1. apollo12

    GT40 Heads

    Nice heads!
  2. apollo12

    New Girl Here

    Welcome to the site
  3. apollo12

    1.7rr on stock long block?

    Did he give you all the hardware or just the roller rockers? If not you will need to order the crane kit to install the rockers
  4. apollo12

    What is this called?

    there is a small circut board(chip board)that plugs into the back of the clusters
  5. apollo12

    91 Mustang GT HELP! wiring problems

    The wires run into the dash harness,wires also run to the ign switch.If you can't find the green connector, I'll give you one just pay for shipping
  6. apollo12

    Cam with stock heads?

    you could go with the b303 or just run the 1.72 roller rockers on your heads and leave the stock cam alone. Using the 1.72's your lift would be .477 instead of the stock .444
  7. apollo12

    what do i need to convert to MAF

    you are 100% correct
  8. apollo12

    will these headers fit?

    shorty headers use the h-pipe/x-pipe for those headers and full length headers use a different h-pipe/x-pipe.If you use full length's you will need adapters for the 02 sensors to make the wires longer
  9. apollo12

    Trying to find the start years for different Mustang Magazines

    I also have a large collection, here is a few old ones I found Hot Rod Magazine "Mustang" fall 1984 vol.2 no.3 SUPER FORD July 1988 Fabulous Mustangs and Exotic Fords May 1985
  10. apollo12

    Tri-State Cylinder Heads - GT40P Heads?

    I just sold a set of gt40 p heads with upgraded springs and fms 1 5/8 headers for $375.00
  11. apollo12

    91 Mustang GT HELP! wiring problems

    ok, I'll look first thing tomorrow
  12. apollo12

    Amazing triple white car

    Nice Mustang but way to much money!
  13. apollo12

    Extremely Weird Problem

    sounds like a bad computer,I had a problem the Mustang would start and idle at 3,000 rpm and wouldn't idle down.I couldn't pull any codes and I wasn't getting a reading on the tps,I put an extra computer in that I had and it ran great
  14. apollo12

    F 303 CAM

    I ran the f303 with 1.6 roller rockers, stock short block and GT40 heads that were milled 40 thousands (60 cc chambers) the mustang ran great. I also have the n-41 in one of my motors with AFR 165 heads, I like the n-41 better but it's a lot more money
  15. apollo12

    91 Mustang GT HELP! wiring problems

    ok,it looks like your is missing the other green connector that would run from up and behind the dash?or are the cut wires the ones that run inside the kick panel and run to power the windows and door locks in the door?I have and extra harness I will look at tomorrow,sorry it's at our shop
  16. apollo12

    LX Tailpipe install Question - Driver Side

    I just did this on one of my Mustangs.Put the rear body(frame) up on jack stands(as high as you can) a good jack in the middle of the rear end,do one side at a time remove the rear bolt of the quad shock,upper control arm bolt on the rear end and the bolt on the shock that connects it to the...
  17. apollo12

    I hate craigslist

    I had a 1989 Mustang GT for sale on craigslist,someone about 100 miles away from me reposted my mustang (pictures and the ad) with his phone number.I posted the link in the lounge on corral.net and let those guy have some fun calling the guy,The guy calls me and says it was a mistake and he's...
  18. apollo12

    91 Mustang GT HELP! wiring problems

    Are you 100% sure you bought a 1991 5.0 computer harness? because that is the only year harness that will work in your 1991 5.0, the 1991 harness will have only 1 plug that plugs into the harness plug on the drivers side, near the brake boaster.When I have a chance I will dig out one of my 1991...