Search results

  1. R

    99-04 Parts

    sold
  2. R

    Coolant in oil

    I am using fel pro gaskets. And I used the assembly lube sparingly. I put a little on the bottom threads so it would track all the way up the stud as I threaded it. I picked up a new filter housing gasket and replaced it, using RTV along with the gasket this time, and refilled my reservoir...
  3. R

    Coolant in oil

    Ok I finally FINALLY got my car running right and I check my oil and there is a lot of coolant in it. I check my coolant and its full of oil. Now Im pretty sure that its not my head gaskets as I had my heads resurfaced and the block is brand new and I installed the gaskets with the engine on a...
  4. R

    Granatelli MAF?

    I moved the IACV vaccum line to the intake before the SC and now the car will idle very roughly (jumps from 500-1000 rpm) but it doesnt die right off the bat. I also ordered a tune from blow by racing. Im home now for a few months then I roll back out
  5. R

    Granatelli MAF?

    Yeah I tried unplugging the maf and starting the car but that didnt keep the car from dying. Im going to route my IACV vaccum line to my intake before the SC and see if that yeilds different results. And patience is good advice, I just want to at least listen to the car cuz between deployment...
  6. R

    Granatelli MAF?

    Im definitely going to get a tune, I just wanted to start the car after months of putting it together. All the vaccum lines are after the maf so its all metered. So essentially I just need a good tune and then the car should idle without dying?
  7. R

    Granatelli MAF?

    Oh another thing: I have my Idle air control valve vaccum line getting pressurized air from the SC. Can it read boosted air?
  8. R

    Granatelli MAF?

    I just finished my build on my 04 GT (Vortech V2, Fully built heads, fully forged block, etc etc). When I start the car if I dont keep my foot on the gas it dies. Its getting good spark and fuel flow there arent any vaccum leaks. I did buy a new Granetelli 90mm MAF and its not programmed. I was...
  9. R

    top 2 trans bolts?? what the easiest way to loosen

    I already had my intake off when I was pulling my transmission so it wasnt really any extra work for me. And it usually only takes me about 30-45 minutes to take off my intake manifold
  10. R

    top 2 trans bolts?? what the easiest way to loosen

    You could also take your intake manifold off and use a wrench to get those two bolts out. Much easier than getting up under the car and using a lot of extensions
  11. R

    Cant find parts!

    I am trying to find a cam cap for windsor heads, both sensors that go on a t56 transmission (speed/tach) and the upper plenum gasket for a PI manifold. I cant find these parts anywhere. Any help would be appreciated.
  12. R

    5.4l headers

    Yeah Im doing the swap because my 4.6 crapped out on me and I picked up a new supercharged 5.4 for a good price. If I have to have a set of headers fabbed I figure I could have a shop cut my current LTs and just make them taller.
  13. R

    5.4l headers

    I am doing the 5.4l swap in my mustang and I have been hearing that because of the height difference in blocks mustang long tube headers wont fit. If this is true does anyone know if long tubes from an F150 would work?
  14. R

    Bolt torque Specs?

    I was wondering what the torque amount was for the cylinder head bolts and the cam cap bolts.
  15. R

    Replacing clutch fork

    Well that sucks. Thanks for the info.
  16. R

    Replacing clutch fork

    Can I replace the clutch fork without pulling the transmission? Can I just disconnect the cover and cable and slide it out that way?
  17. R

    Mail Order Tune

    I need a tune that will account for having no rear O2s and for an EGR delete. Could a mail order tune cover this or would I have to go into a shop and have them do it? I am asking because there are no shops within 3 hours of where I live. This is on a 04 GT with a SCT X2
  18. R

    Bent valve?

    stangman11 I think that you are right about the timing being off. When you set the timing the drivers side cam dowel marks are supposed to be at 12 oclock and the passenger side cam is supposed to be at 11 oclock and the passenger side piston closest to the radiator (just making sure) is...
  19. R

    Bent valve?

    Well I took the head off and it looks like the intake valve on the piston closest to the fire wall just nicked it. The piston isnt damaged it just had a spot on it where all the carbon has been scraped away. The valve is a little messed up though. My buddy owned up to it and is buying my new...
  20. R

    Bent valve?

    Ok well Ill start that tonight. I post what I find.