Search results

hey guys im looking for sme help here i pulled my tranny out to do a clutch, and upon putting it back in the b1s1 plug on the harness side fell in between the block and bell housing. i didnt relize this untill i wento go plug it in. i pulled the trans back outpulled the harness out and put...

Hey haven't posted anything in a long time I am looking for help my rockers as they might be causing my misfire. Here what I am running... 306 with forged DSS flat tops stock crank and rods F-303 cam with stock heads .530 springs stamped steel roller tip rockers and stock length push rod but...

thank you for some one that was able to tell me dot to dot is correct. My family friend told me that dot to dot was wrong n that i needed to pull it out and retarted or advance it. i did torque the rockers to 25lbs i was just say what some one told me to do with them (same family friend) because...

I plan on going through the check list tomorrow i just didnt have enough time to do it today after. I will do it tomorrow and post with what i got. now when i instaled my cam going dot to dot was the proper way right? It dosent need to be advanced or retarted upon install?

compression test numbers 4-125 8-110 3-125 7-110 2-110 6-105 1-85 5-110 These numbers are from doing two revolutions. everything looks good to me but number. I have spark to all plug. I had my little brother helping and you can see flames shooting out of the headers. my plugs...

thank for all the input so far. probly just going to have time for the compression test today after work. hopeing to dig into it this weekend. yes i have pedistal rockers lol i was told that those would be better cuz i wouldnt have to do any adjustments lol:rolleyes:. when i get shims for the...

on to start off heres my set up. 306 with d.s.s forged flat tops, stock rods crank, stock heads, with 580 lift spring 1.6 roller tip rockers stock push rod. F-303 cobra upper lower intake with 1 inch spacer 70 mm T/B. car is S/D 19lbs injectors. The problem is i cant get the car to start...

ok so i havent posted anything in while. but today i took out my hid kit and put reg bulbs in because in selling the car. when i changed them everything seemed to be ok tonight i checked them in the dark great nice and bright and i noticed my high beam light was on. So i checked the switch and...

still have starter, and ground cable to starter relay? thanks

Hey you wouldnt happen to have a starter would you? email- [email protected] thanks

hey guys im replacing the brake line on my car from classic tubing and it dont seem to fit just right:shrug:. i need some referance pictures of the passenger side front brake line from the engine bay to flex line and how its routed thanks alot guys

hey guys i have a QA1 k-member for sale it will fit 1996-2004. its brand new dose have little scratches from test fitting motor ( in fox body) some how got the wrong part number from the parts rep and cant do anything with it now asking 225.00 obo need to get the right one for my car thanks

Found the trim size in the turbo. Its a 63

The turbo is a t3 t4 don't know the trim size yet. But the ultimate question is dose any one think I will have a problem in the furture. I am thinking about going with 30 lbs wit a FMU from a vortech I

hey everyone, ok so i have been building my 306 for the last 7 months, I picked up a turbo kit from a good friend that had lost his car. The turbo kit is now a universal kit do to the fact he bought it for his bmw. What is done to motor is, it's bored out .30 with D.S.S forged flat...

hey guys putting the final touches on my 306 for budget i went with e7 heads im not putting any emissons on the car, and would like to know what sizes the hole are in the back of the head for the emissons tube. dont see the need to spend 10.00 for two bolts

great info thanks i will be tearing into the car tomorrow thanks a lot.

ok so i am getting ready with in the few days to drop my motor in the car. i did some ebgine bay work. i also converted to car to a mass air car. now with that all being said yesterday i finally put the dash back together hooked up the battery to make sure everything was good to go. now wen i...

dose any body know of a bolt size brake down for the engine from the intake to the oil pan. I need a few things to finish the motor and need the bolt sizes and lengths to finish it thanks guys..

hello everyone, Ok to start off i have a 87 gt that was s/d car. i just bought the mass air harness from a buddy ou of an 90 (dont remember if it was a gt or lx). so i get the new harness in and there is and extra gray circle clip by the ecm. and two white ones that are in the engine bay...