Search results

  1. jackson0215

    390 Charging Issue

    Morning, I have all of the sudden developed a charging issue. I have a 67 with a 390. 140A single wire alternator, American Autowire harness, after market air and a stern with a single amp. I can charge the battery and leave the car for a week and come back and it will start fine. I go drive...
  2. jackson0215

    Possible Vacuum Leak 67 Mustang

    I finally started my 67 and I have an issue that I think is a vacuum leak but I wanted to see if anyone else had any ideas. It is a rebuilt 390, new comp cap, new Pertronix distributer, new Quick Fuel Carb and Edelbrock intake. When it starts it takes a little feathering to keep it going and...
  3. jackson0215

    67 Steering wheel gap

    I am down to a couple items on the restoration of my 67 fastback and the steering wheel is giving me fits. There is a 1/4” gap between the steering wheel and the column. I have read about adjusting the column and I have tried that but the column hits the bearing at the top and I can’t get the...
  4. jackson0215

    American Autowire Harness Install

    If the car is gutted already you wil probably have 30 hours in it. This includes figuring out routing, taping and making the terminal connections. Pull all of the wires to their locations before cutting anything. You will pull and move them a couple of times. The other thing to consider is what...
  5. jackson0215

    67 390 FE Alternator Issue

    My hope was to not end to turn the battery tray. Long and short of it CVF ( https://www.cvfracing.com ) has an alternator that is a GM style CS 130 that is only 4.3" deep from the ear to the back. They also have a conversion kit for the difference in threads. I had to order the alternator fan...
  6. jackson0215

    67 390 FE Alternator Issue

    I am in the final stages of finishing up the motor in my 67 and the alternator has brought everything to a stop. I ordered a new bracket kit from CVF racing and when installed it pushes the alternator out past the motor and it hits the battery tray. The adjustment rod won't connect because the...
  7. jackson0215

    67 Spedo Cable

    Evening, I went to install my instrument cluster back into my car and I can not get the speed cable to go into the back. It is a new cable and I unfortunately trashed the old one. The issue is that the metal part that seats into the back of the gauge is hexagonal and where it seats it round...
  8. jackson0215

    SOLD Ssbc Disc/drum Brake Proportioning Valve Ao730

    Brand new SSBC brake proportioning valve. I decided to stick with a stock distribution/proportioning valve. I paid around $85 for it from CJ Pony Parts. Has all 5 inserts and pigtail for the brake lights. I am located in Dallas but I will ship it to you (You pay the shipping). I prefer payment...
  9. jackson0215

    SOLD Ssbc Disc/drum Brake Proportioning Valve Ao730

    Brand new SSBC brake proportioning valve. I decided to stick with a stock distribution/proportioning valve. I paid around $85 for it from CJ Pony Parts. Has all 5 inserts and pigtail for the brake lights. I am located in Dallas but I will ship it to you (You pay the shipping). I prefer...
  10. jackson0215

    67 Instruments Panel Lights

    Anybody know where to find the 2 wire lights for the oil pressure light and the brake light on a cluster harness? If anyone has 2 of them I would also be interested in purchasing them..... Thank you, Mark
  11. jackson0215

    Clutch Question

    Evening, I have a 390 with a 4 speed top loader. I am getting the motor ready to go back in and I not not sure if the ring in the attached picture goes in the place shown or if the bolts go flush to the flywheel. Thank you in advance, Mark
  12. jackson0215

    67 Big Block Clutch Z Bar

    Never mind, it was rusted in the bracket. Had to cut it out and am not ordering a new bracket.
  13. jackson0215

    67 Big Block Clutch Z Bar

    I am trying to figure out how to get the frame side bracket off so I can replace the felt as well as the bushing....Any advice before I tear something up? Thank you as always, Mark
  14. jackson0215

    Rewiring a Classic Mustang

    In my 67 I mounted it to the wiper arm motor bracket.
  15. jackson0215

    Steering Column Wiring/american Autowire Kit

    Heard back from the guys at American Autowire and below is their response. "Thanks for your inquiry, the red wire in your turn signal has no planed function. The red wire has been a mystery and all the Ford wiring documents show no function for such wire. I wish I had a dime for every call I...
  16. jackson0215

    Vintage Air Power Help

    Spoke to Vintage air and they said that you can use the power from the American Autowire kit. The 30 amp fuse needs to be replaced with a 10 am fuse and it is good to go.
  17. jackson0215

    Steering Column Wiring/american Autowire Kit

    I am putting in an American Autowire kit and they list where 9 wires should go but I have 10 in my original 67 steering column. The mystery one is 511B according to the Ford manual but they do not list it's function either. Not sure what to do with this one since it is not listed in the...
  18. jackson0215

    Vintage Air Power Help

    Good Morning, I am in the process of wiring up my vintage air system and I have a question about the violet wire that is said to connect to the run side of the ignition key.....I also put in an American Autowire kit and it has a heater AC feed. It states that it is a fused ignition power lead...
  19. jackson0215

    Engine Harness American Autowire

    Does anyone have a picture of where they drilled the hole in the firewall for the engine feed on an American Autowire harness? he picture in the instructions is not very clear. I have a 67 Fastback. Thank you, Mark
  20. jackson0215

    What Parts Are These?

    Starting to put things back together and cannot remember for the life of me where these go.....It is a 67 fastbavk with a 4 speed and a 390. Thank you!