Search results

Dose anybody use BF Goodrich TA Radials on there Mustang? If so, have you had any problems with them? like the Tread coming off the tire? I took my Babe out for a cruise yesterday and @ 70 Mph the Tread came off my right front tire? and caused a lot of Damage to my front fender and front of my...

I'm having an issue with my 05 GT going in to the " Engine Fail Safe Mode" when I jump on it and run her hard? the car will only go about 5 Mph and when I shut the Motor off and start it up again it will run OK? I put my Code reader on it and it said it Passed with No Codes? How is this...

Well, I purchased a Actron digital Multimeter so I could test and find out the exact voltage. I must have done something right, because at the wire coming from my ignition key I have 12.17 volts with the Key in the On position & this wire is connected to the small Red wire on the MSD box. So. it...

Thank you again for your reply BarnStang. I have the wire that is connected to the MSD box (small red wire) spliced into my ignition switch wire and it has power when checked with a 12 Volt test light. The White wire from the MSD box is taped off and Not used. YES! that is the same spark test...

OK, I'm sorry I guess I'm missing something? Like I said the Engine was running Great with the Model 8350 RTR MSD Distributor installed. All I did was replace the MSD with a shorter Mallory Mag pickup distributor and connect the proper wires per the MSD instructions. All I know is, there is...

Thanks for your reply BarnStang. Yes, the wiring is correct per the MSD instructions for a Mag pickup. the 12 Volts is coming directly from the ignition switch like it always has, and there is No ballest resistor. Funny thing is that it passed the MSD Mag pickup Spark test? So, it's getting...

I also performed a spark test on the MSD and it passed. So, I'm getting Spark with the key in the start position, however Not in the On position. Oh by the way I'm using a Mallory distributor with a Magnetic pickup. Any Ideas anybody??? HELP!

HEY! Thanks for the Tip Missyandrob2005. I don't understand how, but it Works Great. Thank You!

Yes bigb427 that is what I found out @ my local Ford dealer. The replacement Fuel Tank is $1059.00 & the labor is $540.00 WTF! I called Ford and they will Not do anything for me about this issue, even though it is There Problem. My Mustang is an 05 and of course out of warrantee, so I guess Oh...

OK, I checked out all the wiring and here is what I found. With the key @ the On position, I'm getting 12 volts to my MSD Digital 6A box and the red indicator light is on. The Red wire (ignition) from the MSD box is getting 12 Volts from my ignition switch. However, there is Nothing @ the + side...

Thank you again for your reply 69gmachine. I'll try this tonight.

Hello All, Hey, can somebody please till me why I can't fill the gas tank on my 2005 Mustang GT? I have to hold the gas pump nozzle lever in just a little bit and hold it the entire time, and it takes forever to fill the tank? It's a real pain in the Ass. Dose anybody have any ideas?

YES! that is the issue 69machine, thaks for your reply. So, why would that change from just exchanging the distributor? She ran Awesome with the MSD distributor installed, and all I did was install the smaller Mallory distributor that would work with my Shaker hood? Any ideas of what I could try...

Hello All, I have a 1970 Mach 1 with a 351C. I installed a complete MSD ignition system, Distributor, Digital 6A Box, & Coil. The Motor ran Awesome & was a Blast to drive. However, the MSD distributor was to tall to install my Shaker Hood Scoop back on the motor. So, I had to install a Mallory...

Hey, thanks for the reply restomoded66. That is a great idea. Do you know where I could find one?

I finally have my 1970 Mach1 back on the road again, Woo-Hoo! However, I have a little issue with installing my Shaker Hood assembly on my new motor (351C 4v) I installed a complete MSD system # 8350 Pro-Billet distributor, # 6201 Digital box & # 8207 E-Coil. I have now found out that the MSD...

Hello Everybody. Hey, I was wondering what you thought of running an Oil Separator on the PVC system of a 1970 351C 4v? They are getting popular on the New Mustangs. I have already installed one one my 2005 GT & was thinking about installing one on my 1970 Mach1. I can't find a listing for this...

Babe1#7

Babe1#6

Babe1#4