Search results

  1. Monty_Brown

    Mid West If You are in IL IN MI OH WI Register here

    34yr old Mt.Olive IL. live right on good old Rt.66
  2. Monty_Brown

    1966 mustang 86 block

    I have a extra MSD 6A box that came with a project I bought I would sell for $75...it looks nice I can e-mail or text you a picture......
  3. Monty_Brown

    First project car

    If you go that way spend the money on a good set of headers, they make them for the 351w in a 65-66, I would notch the shock towers just for the ease of changing plugs, but its not necessary...it will fit...tight but it will fit.
  4. Monty_Brown

    First project car

    you can buy a complete low milage 5.0 roller motor for the $500 you will have in retro fit roller cam setup.
  5. Monty_Brown

    First project car

    <--I built this 331 from a 89 5.0 roller block, trick flow heads, and trickflow roller valvetrain....easy power and a crap load of aftermarket parts
  6. Monty_Brown

    looking for advice on a carb

    I have the same motor I'm running a Demon 650dp with 3:70 gears and a t-5
  7. Monty_Brown

    I hope I made a mistake sanding my car...

    Off the subject but how did you like the por15??
  8. Monty_Brown

    Motor Mounts

    Good deal!!!!
  9. Monty_Brown

    Motor Mounts

    I also had to change my oil pan, I had a big 7qt pan and it hit the cross member do to lowering the engine, Im now running a moldine 5qt oil pan, wish you luck and let us know if you run into any other issues once you get the mounts installed, I'm running JBA mid-length header and have plenty of...
  10. Monty_Brown

    Which wiring harness?

    The good thing about the american autowire kit is that it relocates the fuse box away from the leaky cowl vent and uses modern ATO fuses and relays and came with a new dimmer and headlight switch, the old fuse box that came out of my car was so rusted up I couldn't have used it, plus I'm going...
  11. Monty_Brown

    Motor Mounts

    Bummer, those mounts will give you plenty of room to wiggle
  12. Monty_Brown

    Which wiring harness?

    I also have the american autowire kit, nice stuff and easy to install and all the wires are labled all the why to the ends. Its on sale right now at Cj Pony parts http://www.cjponyparts.com/AMERICAN-AUTOWIRE-COMPLETE-WIRING-HARNESS-CLASSIC-UPDATE-KIT-1967-1968/p/WHC6768/
  13. Monty_Brown

    Motor Mounts

    I used them mounts to lower my engine, now the air cleaner fits right in the scoop on the shelby hood, I also replace the whole front end on my car.
  14. Monty_Brown

    Motor Mounts

    I would have put a cheap dent in the header to clear the box, sometimes you can heat the header pipe and bend it around a little
  15. Monty_Brown

    Motor Mounts

    I had to use them so my air cleaner would fit in the shelby hood.....I feel your pain, is the front end damaged and out of square?
  16. Monty_Brown

    66 cowl repair help

    I would just patch the bad spots....I went through the same repair, I only replaced one side and POR15 the other side. Yours don't look that bad...
  17. Monty_Brown

    Rearend Swap info - FAQ

    check out www.justrearends.com
  18. Monty_Brown

    Rearend Swap info - FAQ

    My Versailles rear end for my 65 fastback, D-Locker 3:70 moser 31spline axles.....I bought my complete 3rd member from www.justrearends.com guy was easy to work with!!!