Search results

  1. I

    problems getting car started after H/C/I

    had the stock heads ported, rawls cam, lower ported by tmoss, 65mm TB, pro-m 75 meter.
  2. I

    problems getting car started after H/C/I

    ok we got the car started for about a minute, it seemed to run fine. there was alot of noise coming from the rockers, but im assuming thats because they need to seat. anyways, we shut the car off because there was a lil smoke coming from the engine. I later realized thats prolly oil burning off...
  3. I

    What will my set up run?

    what brand street tires do you have? i was able to cut 1.99 60fts with my setup and 245/50 BFG KDW's. it got me in the 13.90's. alot of it is driving rather than how much power your car has. with street tires, launching will be difficult. your best bet would be to keep the rpms up in the...
  4. I

    how much power possible with Ported E7s?

    for reasonable head porting check out greg @ www.xsrcylinderheads.com
  5. I

    Removing Stock Upper/Lower Intake - How hard?

    a vaccum. thats what i did :)
  6. I

    Thinking of extrude hone my stock upper H.O intake...what can I open the TB to?

    i wanted to do all of that, but the welds give it away and extrude hone is too expensive. just gonna open up the stock EGR spacer and upper to 65mm to match my TB.
  7. I

    Feb discount code for trick flows at summit?

    wait how do you get the discount?? i want to buy some band new ones for under 1000!!
  8. I

    My car = Slowest car evar

    i disagree. with his mods and a good driver/traction id say more like mid to high 12s. what mph is ur buddy trapping with his combo and the blower?
  9. I

    Thumper headz

    i think just a drag suspension with slicks would do. tubular k memeber + a arms, coil overs, with good control arms like maximum motorsports. i think alot of it is driving though. jus by learning how to drive and optimizing shift points i got my car to go from a 14.1 to a 13.6
  10. I

    What mods to begin with on a stock 5.0? (I tried searching :)

    for a 5.0 heres what i would do in order: remove air silencer tuneup kit (plugs, wires, cap, rotor, pcv valve) advance timing to 13-16 degrees depending on where your car likes it. U/D pulleys then get a catback, long tubes, and an off road x 3.73 gears drag radials for traction, good...
  11. I

    Shift points on stock rear & 5.0

    ok heres what i did to achieve a [email protected] w/ a 1.88 60ft. 4000 RPM launch on worn out MT 26x10.5 sportsmans w/ only right rear spinning (worn out t-lok) 1st-2nd 5500 RPM 2nd-3rd 5300 RPM 3rd-4th 5100 RPM if i went to the track with slicks that could actually hook, i'm sure i could...
  12. I

    thumper/tmoss bandwagon come on in

    definately goin with the buddy cam after talking to him and some other ppl. ill let everyone know how the combo goes when i start putting it together. ill have plent of questions as i have never done heads/cam/intake before.
  13. I

    thumper/tmoss bandwagon come on in

    TTT anyone wanna share experience with gt40 style or ported stock heads and a custom ground from buddy or ed?
  14. I

    I have $2000 looking for 300hp and low 13's-high 12's

    heres what i would do with 2 grand and ur mods. have the gt40p heads ported, milled, and good springs + rockers. then get a buddy rawls custom ground for $305, full exhaust if u dont already have that, atleast a 3.73 gear, and definately slicks! i think a gt40p/buddy rawls/performer combo...
  15. I

    thumper/tmoss bandwagon come on in

    ok well i got buddy's cam questionnaire and im filling it out right now. after i wrote him a huge email listing the mods to my car and goals, he says with a good driver and traction i should be capable of mid 12s. i know that wont happen right away, im not expecting more then 12.8s. anyways...
  16. I

    Another "What Mod to do Next" Thread!!! (tax refund)

    all of those really good ET's are from one thing and thats hard ass launches. id definately get some nitto's or bfg's for the street and mt 26x10.5 for the track. then id do mm adjustable upper and lower control arms, reinforce torque boxes, then save for an Eaton posi.
  17. I

    thumper/tmoss bandwagon come on in

    TTT how can i get ahold of buddy and has anyone had actual experience of one of his custom grounds with stock heads?
  18. I

    thumper/tmoss bandwagon come on in

    ok whats the best way to contact buddy? email me at [email protected] if u dont wanna post up his phone number on here. i know he has a website explaining alot of stuff about engines and cams and also shares a little background of him. i really wanna go custom with this. heres a list of...
  19. I

    thumper/tmoss bandwagon come on in

    dude i agree with u, theres nothing like going sideways in a 5oh