Search results

Warning about Wheel Spacers :notnice: Everyone, I had a set of H&R 1" (25mm) rear only spacers on my 03 GT and they caused my outer bearings to go bad. After 3 months installed the rear is now howling. The car is driven daily and is not raced. Just food for thought before you decide to spend...

I've got an 03 that does the same thing. Ford said there is nothing wrong after several trips to the dealer and the Ford area rep. The general feeling is this is the fuel injectors pulsing under acceleration. Some feel it may be the defective heads but you decide after you read thr article...

Everyone, I've got an 03 GT Auto with almost 15,000 miles on it and I just noticed a rear end noise (howling) within the last few weeks. The rear is stock only did an oil change and installed Redline Oil with Summit dif pan. What I did do back in January was install 1" H&R wheel spacers. Q...

For those who have installed a Steeda Tower Strut. I have and 03 GT and when you put the strut into place it's about a 1/4 inch short of contacted the rear area. Wondering if upon installation it will pull that 1/4 inch in when tightened?

How Much of a Pitch? I've got Steeda Sports and it lowered my front end around 1 1/4. My tie rods are also pitched up a bit but don't think that's a problem. Go look at any stock mustang and see what the tie rods look like, I think you will find they all look that way!

Paint Code Sonic Blue is paint code SN

I installed an Autometer Lunar Trans Temp Gauge. The gauge works fine but my issue is with the lighting. I tapped a wire (brown in my 03) that when the light switch is pulled to park the gauge lights up but had no dimming control on the AM gauge. So I tapped the dimmer light wire (BL/WT) to the...

Anyone out there have a 2 point tower strut installed on their 03 GT or late model? Just wondering if the 2 point strut is as good as the 3 point?

Ford Motorsport :flag: Check this out Ford Motorsport has what your looking for. http://www.performanceparts.ford.com/parts/part_details.asp?PartKeyField=6306

Just wondering if someone who has installed an Autometer Elec Water Temp Gauge could give me some advice. Should I tap a 1/8 NPT hole on the boss next to the thermostat or is there a better place to connect the sender? Please help with pics if you have them. Thanks

I have an 03 GT and I was wondering if upper and lower aftermarket control arms are worth the money? Is it nessessary for a daily driver who does not race the car?

Tap the wire I installed an Autometer trans temp gauge on my 03 GT, and for lighting I taped the brown wire at the light switch. This wire is hot when lights are in turned on to the parking light position. I have not had any light issues doing it this way.

Need advice as to which Oil Cooler is the best?

Sender Mounting Mounted the sender in the tranny at the pipe fitting plug on the left side. It's a 1/8 hole and the sender fit with no leaking. In wound up mounting the ground at the same spot you did. It's working fine because I had the ground in another location near the sender and the...

I'm installing an Autometer Trans Temp Gauge and I'm having problems with where to place the ground wire for the sender. Can someone suggest a place for a good ground.

I just installed a Digital Trans Temp gauge. Everything is working but the gauge lights a flickering. Could it be I don't have a good ground?

Pods and Gauges Pods come in single, double, and triple. They also have a single pod that fits on the steering column. Just search the net and you'll find what your looking for.

Accufab 70mm TB/intake plenum/intake spacer I've got the same setup on my 03 GT. Check your old TB and see if it has a IDLE SCREW you can adjust. On the newer models like mine there is no idle screw just a plug that Ford put in. I had the same exact problem untill I found out Accufab TB came...

Steeda CC Plates Guys I had the Steeda 3 bolts plates installed and every time you hit a bump in the road "CLUNK". I checked my installation several times and could not find anything wrong. I got tired of hearing this clunk all the time so I went back to the stock setup. Alignment is still...

Has anyone installed the pump? (MEZIERE ELEC WATER PUMP) Pros and Cons, charging, water temp, increase in power!