Search results

  1. J

    Trans cooler line routing problem

    Have you burned any yet? I dont really understand, isnt it different then a Mustang? I mean I guess its basiclly the same setup, right? Are you runnin longtubes? Okay from the trans straight forward, between the dipstick and the trans, over the starter and then down. Did you put any kind of heat...
  2. J

    Trans cooler line routing problem

    Im from Jonesboro Arkansas. To the guy with the T Bird, are you running all rubber lines?
  3. J

    Trans cooler line routing problem

    Heres the story, I have an 87 GT with a Lentech auto and Mac longtube headers. When I installed the trans I junked the factory cooler lines and just used rubber ones on the new TCI trans cooler. Heres the problem headers get hot, rubber lines dont like heat. Ive gone through two lines and it...
  4. J

    Trans Pan Leak

    Alright, I bought a Lentech trans and at the 500 mile service interval I changed the filter and pan gasket. Well it was leaking pretty bad so yesterday I thought Id change it, better go ahead and bite the bullet, you know its an expensive trans. Went ahead and changed the filter while I was in...
  5. J

    What the Crap? (Lt headers)

    Okay, here we go. Bought some Mac Longtube headers, for my AOD 87 Mustang, from Jet Hot. They looked awsome, bitch to put in, but once they were in it was on, I was so excited. Then I got to putting in the O2 sensors and noticed the bungs were on the outside :shrug: , Oh well, theyll still work...
  6. J

    Will this destroy Tranny?

    Or you could just get a Lentech Street Terminator Plus that holds 700 HP and not worry about wether it will hurt the trans or not. AODs suck? I havent ever missed a gear...how bout them 5 speeds? :shrug:
  7. J

    Sub Frame Paint

    Just ordered some Steeda full length subframe connectors. Got an awsome deal, the only problem is this, they need to be painted. So heres my question,what kind of paint should I use? Just some Krylon? Thanks for the help, Josh
  8. J

    Fuel Cell Install

    My buddy has an 85 Cougar we are going to put an 8 gallon fuel cell in. Heres the problem, someone told us that we have to cut a hole in the floor of the trunk so the two lines and the hump thing can hang outside of the car. Ive never done this and have no idea why that has to hang out. :shrug...
  9. J

    automatics slower than 5 speed?

    Depends on if the guy in the 5spd can drive or not. Ive raced several 5spd cars with a stock AOD and beatem by 2 or 3 cars. They start off jumping me out of the hole, but each time they shift they fall back about a half car, and if they miss a gear its over. Ive never missed a gear with my AOD...
  10. J

    87-89 Guys in here!

    Thank you, thats exactly what I was lookin for. Josh
  11. J

    87-89 Guys in here!

    Ok heres my problem, on the 87-89 cars there are some dummy lights on the lower right hand side of the cluster bezel. When my car got stolen they tore that plastic indicator up. I just need to know what the lights stand for, I know that there is a low oil light, I belive its the top left of the...
  12. J

    First run at the track

    Hey Rdksek844, what all have you got done to your car? I know you said bonestock motor, but is the car like, off the showroom floor stock? Do you have gears? Pulleys? Exhaust? Shifter? Anything? Thanks, just curious. Josh
  13. J

    Speedo or Trans Question

    I have a Lentech Street Terminator Plus in my 87 GT. I have 225/60R15 tires, and 3.73 rear gears. I have a 21 tooth speedo gear and my speedo is still 10 MPH fast. Lentech said I could get a 23 tooth but didnt say that would fix it. Any ideas on where I could get one? Any one with a Lentech have...
  14. J

    NITROUS guys, quick Question

    Im running a ZEX dry kit on my 87 GT. It just has an arm swith on the inside of the car. But you slpice into the TPS and connect the wire to the box and thats it. Arm it floor it and go. Im really happy with this kit except itll only go to 125hp. One more thing, if you do get a kit from anyone...
  15. J

    Not really a discount...

    I posted earlier today about the Group Purchase, I dont know if it got taken off or what but nobody said I did anything wrong so Ill rewrite it. The thing is that the GP price on the Flowmaster cat back is not a deal at all. They say its 226.95 with the discoutnt for the FLO-17113. I have a...
  16. J

    Heres a tough one

    Ford has what I think is called FMEM, I think its Failure Mode Effects Management. When a sensor goes bad the computer takes the last known good reading and runs off of it. I know thats how it works but Im not sure of the name. And plus my plugs looked good.
  17. J

    Heres a tough one

    O2 sensor wont make it miss.
  18. J

    Heres a tough one

    No I just got the street terminator plus, no transbrake or manual valvebody. Its goin in this weekend Ill tell you how it works out. Let me ask you a question, how often do you use your OD? I have a pretty stock motor with 3.73 and on my way to work I have some pretty long stretches of 55MPH...
  19. J

    85 MPH to 140 MPH speedo

    Yeah 87 and 88 had the 85MPH speedo...all year.
  20. J

    Header Gaskets?

    Im about to order some MAC full lengths from JET HOT and was wondering what kind of gaskets yall recomend? Pretty simple question, Thanks Josh